Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A replacement tandem roller carriage for a sliding closet/wardrobe door, 70 x 30 x 13.6 mm, that runs on two standard 608 skate bearings (8 x 22 x 7 mm) spaced 38 mm apart on integral 7.7 mm stub axles with M3 retainer bolts. Four 4.5 mm M4 holes in two rows 8 mm apart let you set the door ride height when the original nylon wheels have collapsed and the part is no longer sold.
A no-drill C-clamp that hooks over the front lip of a K-style rain gutter and carries a security camera or its solar panel on a 13 mm long 1/4-20 slot, so renters and anyone with aluminium soffits never touch the fascia. The 26 mm throat is closed by two M4 screws in 5.5 mm heat-set insert bores (use M4 x 30), gripping lips and beads from 5 to 24 mm deep; overall 74 x 44 mm with a 30 mm wide jaw, and it prints with zero overhangs because the whole profile is extruded along the gutter run.
A screw-clamped replacement tine for a dishwasher rack: a split saddle grips any coated rack wire from 4.6 to 6.6 mm and carries a 48 mm tapered fin that holds plates apart where the original tines snapped or rusted through. 59 x 21 x 36 mm, closed by two M3 x 20 stainless screws into M3 heat-set inserts (4.0 mm bores), with six drain cutouts; print in PETG.
Replacement control knob for a washer, dryer, range or toaster oven whose original plastic shank has cracked and stopped gripping the timer shaft — 48 mm diameter, 22 mm deep, with a 6.8 mm bore that slips over 1/4 in (6.35 mm) and 6 mm round or D-shaped shafts. A radial M3 brass heat-set insert (4.0 mm bore) takes an M3 x 10 set screw that clamps onto the shaft flat, so one knob body covers a family of shafts instead of a $40-120 timer assembly; 14 finger flutes and a moulded pointer fin read the dial position.
A wall bracket that stops a long curtain rod sagging in the middle: a 90° V saddle self-centers any rod from 16 to 28 mm OD (5/8" to 1-1/8") with the rod axis 45 mm off the wall, and two cable-tie slots break into the groove so one zip tie traps the rod against lift-out. The 6 mm wall plate takes two M4 (#8) screws on a 28 mm vertical spacing, the saddle is 18 mm wide along the rod, and the whole 64 x 44 x 18 mm part is a single vertical-walled prism that prints flat with no supports.
A split-band clamp that grips a standard round door knob (50–56 mm, eleven internal 1.25 mm grip ribs) and adds a 95 mm lever arm so the door opens with a forearm, elbow or closed fist instead of a twisting grip. One M4 bolt through the 4.5 mm clearance ears pulls the 4 mm split shut onto a captured M4 nut; band is 22 mm tall, arm 14 mm thick, overall 139 x 63 mm, and it prints flat with the lever load in the XY plane.
A split clamp for a 31.8 mm handlebar that carries a second 22.2 mm accessory bar stub 55 mm out to the side, so lights, a GPS, a bell and a phone mount stop fighting for stem space. Closed by two M5 bolts with captured nuts, 99 x 44 x 55 mm, gusseted web under the stub.
A clamp-on shelf that straddles the top bezel of a monitor and gives a webcam, action cam or small light a solid 41 mm deep platform with a 6.8 mm obround slot for a 1/4-20 tripod screw (14 mm of fore/aft travel) and a 3 mm anti-slide lip. The 18 mm wide throat swallows panels from about 5 mm to 18 mm thick and locks with an M4 x 25 screw into an M4 heat-set insert (5.5 mm bore) in the rear jaw, so nothing presses on the screen; two M3 clearance holes in the deck take a light arm or adapter plate. Overall 78 x 34 x 42 mm, printed as a single profile with no overhangs or supports.
A C-clamp that grips a desktop 12–30 mm thick and holds a vertical 2020 extrusion post at the desk edge, so you can mount a lamp, mic boom, webcam or a small shelf without drilling the desk. 99 x 38 x 30 mm body with a 20.4 mm square socket 40 mm deep (two M5 clearance holes for T-nuts lock the post) and two M4 heat-set inserts in the lower jaw for the M4x30 clamp bolts; the flat 38 x 30 mm upper jaw pad bears on the desk surface and the rear face registers flush against the desk edge. Prints flat on the plate, no supports.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A cable-tie-on bottle cage mount for bikes with no braze-on bosses: a 26 x 26 x 90 mm block with a 90-degree V groove that self-centres on round tubes from about 22 to 32 mm, and two M5 cage bolt bores on the standard 64 mm boss spacing with captured 8 mm hex nuts loaded from the side. Two 8 x 2.8 mm tunnels take 4.8 mm standard or 7.6 mm heavy-duty zip ties that wrap the tube and pull the groove down onto it.
A clamp-on comb that grips the back edge of a desk or shelf (tops up to 27 mm thick) and drops five cables down in separate channels instead of one tangled bundle — two 10 mm channels for laptop/power bricks and three 7 mm channels for USB and audio leads, each with a snap-in mouth so cables push in from the side and stay put. 57 mm wide, 42 mm tall, no drilling: an M4 brass heat-set insert (5.5 mm bore) in the lower jaw takes an M4 x 20–25 bolt that jacks up against the underside of the desktop.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A one-handed reading aid: slip your thumb through the 22 mm ring and the two 29 mm wings press both page blocks flat so a paperback stays open by itself. Ramped wing tips slide under the pages without creasing them; 80 mm wide overall.
A 110 mm wall-mounted entryway rack with a 38 mm deep pocket for letters and bills plus three angled hooks with catch lips for keys. Two keyhole slots let it drop onto drywall screws at 88 mm spacing.
A slip-on soft jaw cap for a bench vise: the tapered channel wedges onto jaw plates 12.5–16.5 mm thick, and crossed 90° V-grooves cradle round bar either horizontally or standing upright. 80 mm long, 30 mm tall — print two, one for each jaw.
A hollow, rib-cored riser that lifts a bed, couch, desk or dresser leg 44 mm for extra under-furniture storage. The chamfered 58 mm socket accepts square or round legs, and a poke-out hole in the floor frees a stuck leg — order four for one piece of furniture.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
An 80 mm L-block that holds two boards at a true 90° while glue sets, with open windows so a spring clamp reaches straight through to the workpiece and a rounded corner relief for squeeze-out. Two 4.5 mm holes let you screw it down to a bench or assembly board.
A shelf that hangs on the center screw of a standard duplex outlet cover to hold a charging phone off the floor. 70 mm wide plate, 58 mm deep ledge with an 8 mm lip and a cord notch through the middle.
A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.
A winding key that grips the flat tail of a toothpaste or ointment tube in a 3.2 mm slot; twist the finger-hole knobs to roll the tube up and push every last bit out. 96 mm long with a Ø7 mm hang hole in one knob.