Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A split-band clamp that grips a standard round door knob (50–56 mm, eleven internal 1.25 mm grip ribs) and adds a 95 mm lever arm so the door opens with a forearm, elbow or closed fist instead of a twisting grip. One M4 bolt through the 4.5 mm clearance ears pulls the 4 mm split shut onto a captured M4 nut; band is 22 mm tall, arm 14 mm thick, overall 139 x 63 mm, and it prints flat with the lever load in the XY plane.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A one-handed reading aid: slip your thumb through the 22 mm ring and the two 29 mm wings press both page blocks flat so a paperback stays open by itself. Ramped wing tips slide under the pages without creasing them; 80 mm wide overall.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A tapered split collar that drops into an oversized patio-table umbrella hole and wedges the pole tight so it stops rattling and leaning. Suits ~38 mm poles in 44–52 mm table holes; 68 mm flange rests on the tabletop.
A 110 mm wall-mounted entryway rack with a 38 mm deep pocket for letters and bills plus three angled hooks with catch lips for keys. Two keyhole slots let it drop onto drywall screws at 88 mm spacing.
A 95 x 70 mm catch-all tray with two compartments for keys and coins plus an upright slot that stands a phone (up to 13 mm thick with case) face-up on a raised shelf. A tunnel through the back wall feeds the charging cable up to the phone's port so the cord never leaves the dock.
A hollow, rib-cored riser that lifts a bed, couch, desk or dresser leg 44 mm for extra under-furniture storage. The chamfered 58 mm socket accepts square or round legs, and a poke-out hole in the floor frees a stuck leg — order four for one piece of furniture.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
A two-horn wall cleat for figure-eight wrapping an extension cord, air hose or rope, with flared post tips that keep the coil from slipping off. 120 mm wide, mounts with two countersunk screws and holds roughly a 50 ft 16-gauge cord.
A shelf that hangs on the center screw of a standard duplex outlet cover to hold a charging phone off the floor. 70 mm wide plate, 58 mm deep ledge with an 8 mm lip and a cord notch through the middle.
A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.
A winding key that grips the flat tail of a toothpaste or ointment tube in a 3.2 mm slot; twist the finger-hole knobs to roll the tube up and push every last bit out. 96 mm long with a Ø7 mm hang hole in one knob.