Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A one-piece dust-extraction adapter that joins a 2-1/2 in (63.5 mm) shop-vac hose to a 1-1/4 in (31.75 mm) power-tool dust port — a 64.0 mm socket with an internal 45° stop shoulder steps down through a tapered cone to a 31.4→30.6 mm friction spigot with a seating flange. 79 mm tall, 78 mm across the three grip ribs, with a 3.4 mm M4 self-tapping screw hole through one rib so the hose can be locked instead of pulling off mid-cut.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A 120 mm bench-top miter box with guided 90° and left/right 45° saw slots for cutting trim, dowels, and small stock by hand. The channel takes pieces up to 34 mm wide and about 20 mm thick, and two counterbored holes let you screw or clamp it to a bench.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A handheld drill guide with five tall bushing towers (3.2, 4.2, 5.2, 6.4 and 8.2 mm) that keep a bit perfectly perpendicular, plus a 90° V-groove underside that self-centers the holes on dowels and round stock. Block is 102 x 36 x 44 mm.
A palm-sized sanding block with a flat 88 x 68 mm face and a contoured grip; a quarter sheet of sandpaper wraps the bottom and tucks into the two tapered slots on the end shoulders, which wedge tighter as you sand. Hollow-cored so it stays light and cheap to print.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
An 80 mm L-block that holds two boards at a true 90° while glue sets, with open windows so a spring clamp reaches straight through to the workpiece and a rounded corner relief for squeeze-out. Two 4.5 mm holes let you screw it down to a bench or assembly board.
A 90 mm V-jaw layout plate that drops over the end of any round bar, dowel or pipe from about 9 to 70 mm diameter; scribe through the long centre slot, rotate the stock 90° and scribe again — the crossing point is dead centre. The 8 mm deep V lips self-centre the tool so it can't rock off the end face.
A weighted-footprint cradle that holds a closed laptop, tablet or notebook upright on the desk, with a 22 mm slot, chamfered lead-in edges and a cable pass-through slot in the floor. 90 × 70 × 50 mm.