Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A bench-top fume extractor housing for any 40 x 40 x 10 mm fan — the fan bolts to the 60°-tilted face on its standard 32 mm M3 pattern (3.4 mm clearance holes with counterbores so the heads sit flush), and a 42 mm square of activated-carbon filter sheet press-fits into the 41.5 x 41.5 x 4 mm pocket in front of a ribbed finger-guard throat. Footprint 52 x 64 mm, 50 mm tall, with two M4 holes in the weighted base for bolting it to the bench and an open rear duct so exhaust clears the work.
A standoff bridge that suspends a 40 mm fan directly over a Raspberry Pi 4B / 3B+, with a 32 mm shrouded duct collar aiming the air at the SoC instead of letting it spill sideways. 74 x 64 mm plate on four 18 mm legs that clear the USB/Ethernet stack, 58 x 49 mm M2.5 board pattern with captured nuts at the board end, 32 mm square M3 fan pattern, plus side exhaust vents and a 26 x 4.5 mm slot for GPIO ribbon or camera flex.
A 104 x 46 x 16 mm bench dock that stands up 6 microSD cards (11 x 15 x 1 mm), 3 full-size SD cards (24 x 32 x 2.1 mm) and 4 USB-A flash drives parked plug-down in 12.8 x 5.4 mm bays, so the loose media around a Pi/camera bench stops disappearing into the parts bin. Cards protrude 7–20 mm for a one-finger pinch, a scalloped thumb groove backs the microSD row, and two M3 clearance holes on a 96 mm centre let you screw it into a drawer bottom or shelf; underside relief pockets keep it to roughly 57 cm³.
A stackable 96 x 84 x 28 mm deck for Raspberry Pi 4B / 3B+ cluster builds: each board bolts to four 6 mm standoffs on the verified 58 x 49 mm pattern with 2.9 mm holes for M2.5 screws, and the 14 mm corner posts peg into the socket of the deck above for a 28 mm stack pitch (16 mm of free air over each board for a HAT or fan). Three large windows give vertical airflow, plus two 4 mm cable-tie slots and two M3 clearance holes so the bottom deck can be screwed to a wall or panel.
A six-lane stadium-step rack that sorts cut heat-shrink tubing by diameter — troughs 8/10/12/14/17/20 mm wide take the common 3:1 sizes from 2.4 mm up to 12.7 mm, each 74 mm long with a finger scallop so you can pinch a piece out without emptying the lane. 116 x 99 x 39 mm overall, open underneath to stay light, with two M4 clearance ears (4.5 mm) to screw it to a shelf or bench back.
A 110 x 62 mm vented backplate for a Raspberry Pi 4B / 3B+ with four 5 mm standoffs on the 58 x 49 mm bolt pattern (2.9 mm bores for M2.5 screws), edge stiffening ribs, two keyhole slots that drop over #8 wall screws, an M4 lock hole at the bottom, and a zip-tie bridge for power-cable strain relief. Five long vent slots keep air moving under the board and cut print time.
A 147 mm staircase block that stands a 13-piece metric drill index upright, with bores from 1.5 mm to 7.5 mm rising left to right so the size order is obvious at a glance. Each step is taller than the last, so bit tips sit deep and shanks stay easy to grab.
A weighted-footprint cradle that holds a closed laptop, tablet or notebook upright on the desk, with a 22 mm slot, chamfered lead-in edges and a cable pass-through slot in the floor. 90 × 70 × 50 mm.