Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A standoff bridge that suspends a 40 mm fan directly over a Raspberry Pi 4B / 3B+, with a 32 mm shrouded duct collar aiming the air at the SoC instead of letting it spill sideways. 74 x 64 mm plate on four 18 mm legs that clear the USB/Ethernet stack, 58 x 49 mm M2.5 board pattern with captured nuts at the board end, 32 mm square M3 fan pattern, plus side exhaust vents and a 26 x 4.5 mm slot for GPIO ribbon or camera flex.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A stackable 96 x 84 x 28 mm deck for Raspberry Pi 4B / 3B+ cluster builds: each board bolts to four 6 mm standoffs on the verified 58 x 49 mm pattern with 2.9 mm holes for M2.5 screws, and the 14 mm corner posts peg into the socket of the deck above for a 28 mm stack pitch (16 mm of free air over each board for a HAT or fan). Three large windows give vertical airflow, plus two 4 mm cable-tie slots and two M3 clearance holes so the bottom deck can be screwed to a wall or panel.
A 110 x 62 mm vented backplate for a Raspberry Pi 4B / 3B+ with four 5 mm standoffs on the 58 x 49 mm bolt pattern (2.9 mm bores for M2.5 screws), edge stiffening ribs, two keyhole slots that drop over #8 wall screws, an M4 lock hole at the bottom, and a zip-tie bridge for power-cable strain relief. Five long vent slots keep air moving under the board and cut print time.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
A stand-on jack that pulls muddy boots off without touching them: the heel drops into a tapered 20–55 mm V while your other foot holds down the slotted deck. 135 × 60 × 32 mm, prints flat with no supports.