Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A print-in-place rotary output stage for a NEMA 17 stepper joint: a Ø52 mm race bolts to the 31 mm square M3 faceplate pattern and sits over the 22 mm pilot boss, while a captured rotor clamps to the 5 mm shaft (Ø5.3 bore, M3 grub screw in a radial heat-set insert) and carries the arm on four M3 heat-set bosses in a 16 mm square. The printed race takes the radial and moment load that would otherwise destroy the motor's own bearings; total height 25.5 mm, two pieces, no assembly.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A 62 mm square, 19 mm tall adapter that lets a NEMA 17 stepper bolt into a machine face drilled for NEMA 23 — the base carries the 47.14 mm M5 pattern, the raised Ø52 tower carries the 31 mm M3 pattern with a 22.4 mm pilot register for the motor's centring boss. The hollow Ø30 core clears a shaft coupler, a 14 mm side window gives Allen-key access to the coupler set screw, and counterbores in the base bottom fully recess the four M3x20 motor screws so the adapter still seats flat.
A vibration-isolating NEMA 17 motor mount: the motor bolts to a floating 46 mm plate (31 mm square M3 pattern, 22.5 mm pilot-boss bore) that is joined to a 76 x 76 mm outer frame only by four Z-shaped flexure beams, so motor buzz never reaches the chassis or the gyro. The frame bolts down with four M3 screws on a 68 mm cross pattern; print it as shown (flat, no supports) and flip it in use so the motor plate floats 6 mm clear of the chassis, leaving room for the motor screw heads.
A printed beam-flexure shaft coupler that joins a 5 mm stepper shaft (NEMA 17) to an 8 mm T8 leadscrew, with three 60°-indexed relief slots so it absorbs misalignment instead of binding the nut. 20 mm OD x 44 mm long, 5.3 mm and 8.6 mm bores, four M3 self-tapping grub screws (two per hub at 90°).
A 60 mm OD × 18 mm wide spoked drive wheel that slips onto any 5 mm motor shaft (NEMA 17, 37 mm gearmotor) and locks with an M3 set screw threaded into the 6.3 mm hub wall. The 8 mm × 2.5 mm rim groove seats a #64 rubber band as a tire, and 24 scallops in the flanges give traction if you run it bare — replaces the hub-and-tire set nobody stocks for one-off robot builds.
An L-bracket that mounts a NEMA 17 stepper to 2020 aluminium extrusion: 54 x 40 mm base with two M5 T-nut holes on 20 mm centres, and a 54 x 50 mm vertical face carrying the 31 mm square M3 bolt pattern plus a 22.6 mm pilot bore for the motor's centring boss. Twin 5 mm gussets carry motor torque in the strong XY direction and sit outboard of the bolt heads so a hex driver still reaches all four screws; a pair of 6 x 3 mm slots above the bore takes a cable tie for the motor lead.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
A 100 x 72 mm bar-soap dish with a 3 mm sloped floor, five lengthwise ribs that keep the bar up out of the water, and a spout notch with a flat drip tongue that sends runoff into the sink instead of onto the counter.
A two-compartment caddy that sits beside the faucet to hold a sponge and scrub brush separately, with slotted drain holes in the bottom so water runs out instead of pooling. Fits a standard sponge; overall footprint 100 x 70 x 45 mm.