Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A replacement tandem roller carriage for a sliding closet/wardrobe door, 70 x 30 x 13.6 mm, that runs on two standard 608 skate bearings (8 x 22 x 7 mm) spaced 38 mm apart on integral 7.7 mm stub axles with M3 retainer bolts. Four 4.5 mm M4 holes in two rows 8 mm apart let you set the door ride height when the original nylon wheels have collapsed and the part is no longer sold.
A screw-clamped replacement tine for a dishwasher rack: a split saddle grips any coated rack wire from 4.6 to 6.6 mm and carries a 48 mm tapered fin that holds plates apart where the original tines snapped or rusted through. 59 x 21 x 36 mm, closed by two M3 x 20 stainless screws into M3 heat-set inserts (4.0 mm bores), with six drain cutouts; print in PETG.
Replacement control knob for a washer, dryer, range or toaster oven whose original plastic shank has cracked and stopped gripping the timer shaft — 48 mm diameter, 22 mm deep, with a 6.8 mm bore that slips over 1/4 in (6.35 mm) and 6 mm round or D-shaped shafts. A radial M3 brass heat-set insert (4.0 mm bore) takes an M3 x 10 set screw that clamps onto the shaft flat, so one knob body covers a family of shafts instead of a $40-120 timer assembly; 14 finger flutes and a moulded pointer fin read the dial position.
Replacement side-wall channel clip that carries a 1/4 in (6 mm) glass shelf in an old steel or wood medicine cabinet, for when the original stamped clips are long discontinued. The 90 x 22 x 16 mm body has a 6.8 mm wide, 12 mm deep channel with a flared lead-in and a closed back stop, plus two 3.4 mm M3 clearance holes 70 mm apart on tabs clear of the jaws so a screwdriver reaches; the flat 4 mm back also takes VHB tape if you can't drill the cabinet. Symmetric about its centreline, so the same print flipped over serves the opposite wall — print two.
Replacement bottom guide for a bypass/sliding shower door: a 46 x 22 x 15 mm block that screws to the track with two countersunk M3 (#6) screws and carries the door's bottom glass edge in a 7.2 mm channel sized for 1/4 in (6.35 mm) glass. A V-shaped lead-in opens the channel to 12.7 mm at the rim so 5/16 in and 3/8 in glass still ride about 5 mm deep, and flared ends in plan view guide a drifting door back in; the counterbored screw holes also drain the channel.
Replacement wall-end bracket for a broken towel bar, with a stepped socket that takes both 1 in (25.4 mm) and 3/4 in (19 mm) tube — a 1 in bar bottoms on the step after 18 mm, a 3/4 in bar slides 28 mm deep — and an M4 set screw that locks it so you don't have to replace the whole rail set. Back plate is 42 x 68 x 6 mm with two counterbored 4.5 mm holes 52 mm apart for #8/M4 anchors, bar centre stands 38 mm off the wall, overall 55 mm tall.
A 120 mm replacement flush lever arm for a toilet tank, for when the brittle OEM arm snaps at the chain hole and the linkage isn't sold separately. Instead of guessing your handle's tab shape, a 14 mm deep forked jaw slides over the handle blade (1.5–3.6 mm thick) and pinches it with an M3×20 screw and a captured M3 nut; five 4 mm chain holes on a 12 mm pitch set the flapper chain length. Arm cross-section is 5 × 12 mm so the bending load runs along the print's strong axis.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A 120 mm slide-on splint sleeve that repairs a snapped 11 mm tent pole section: 11.4 mm teardrop bore (0.4 mm slip fit), 4 mm walls, tapered lead-in mouths at both ends, and two M3 self-tapping set-screw bosses (2.6 mm holes) that pin it to each pole half so it can't migrate off the break. A centre notch in the full-length stiffening rib lines it up on the crack; overall 120 x 19.4 x 22 mm with a flat printed pad on the bottom. Print in PETG or ASA for UV and cold tolerance.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A soil spike that turns an empty soda bottle into a slow-drip plant waterer — press the inverted bottle neck into the ribbed socket and push the 140 mm spike into the pot. Three staggered drip ports feed water down at the root zone while the 44 mm flange keeps it from sinking.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.