Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A replacement tandem roller carriage for a sliding closet/wardrobe door, 70 x 30 x 13.6 mm, that runs on two standard 608 skate bearings (8 x 22 x 7 mm) spaced 38 mm apart on integral 7.7 mm stub axles with M3 retainer bolts. Four 4.5 mm M4 holes in two rows 8 mm apart let you set the door ride height when the original nylon wheels have collapsed and the part is no longer sold.
A screw-clamped replacement tine for a dishwasher rack: a split saddle grips any coated rack wire from 4.6 to 6.6 mm and carries a 48 mm tapered fin that holds plates apart where the original tines snapped or rusted through. 59 x 21 x 36 mm, closed by two M3 x 20 stainless screws into M3 heat-set inserts (4.0 mm bores), with six drain cutouts; print in PETG.
Replacement control knob for a washer, dryer, range or toaster oven whose original plastic shank has cracked and stopped gripping the timer shaft — 48 mm diameter, 22 mm deep, with a 6.8 mm bore that slips over 1/4 in (6.35 mm) and 6 mm round or D-shaped shafts. A radial M3 brass heat-set insert (4.0 mm bore) takes an M3 x 10 set screw that clamps onto the shaft flat, so one knob body covers a family of shafts instead of a $40-120 timer assembly; 14 finger flutes and a moulded pointer fin read the dial position.
Replacement side-wall channel clip that carries a 1/4 in (6 mm) glass shelf in an old steel or wood medicine cabinet, for when the original stamped clips are long discontinued. The 90 x 22 x 16 mm body has a 6.8 mm wide, 12 mm deep channel with a flared lead-in and a closed back stop, plus two 3.4 mm M3 clearance holes 70 mm apart on tabs clear of the jaws so a screwdriver reaches; the flat 4 mm back also takes VHB tape if you can't drill the cabinet. Symmetric about its centreline, so the same print flipped over serves the opposite wall — print two.
Replacement bottom guide for a bypass/sliding shower door: a 46 x 22 x 15 mm block that screws to the track with two countersunk M3 (#6) screws and carries the door's bottom glass edge in a 7.2 mm channel sized for 1/4 in (6.35 mm) glass. A V-shaped lead-in opens the channel to 12.7 mm at the rim so 5/16 in and 3/8 in glass still ride about 5 mm deep, and flared ends in plan view guide a drifting door back in; the counterbored screw holes also drain the channel.
Replacement wall-end bracket for a broken towel bar, with a stepped socket that takes both 1 in (25.4 mm) and 3/4 in (19 mm) tube — a 1 in bar bottoms on the step after 18 mm, a 3/4 in bar slides 28 mm deep — and an M4 set screw that locks it so you don't have to replace the whole rail set. Back plate is 42 x 68 x 6 mm with two counterbored 4.5 mm holes 52 mm apart for #8/M4 anchors, bar centre stands 38 mm off the wall, overall 55 mm tall.
A 120 mm replacement flush lever arm for a toilet tank, for when the brittle OEM arm snaps at the chain hole and the linkage isn't sold separately. Instead of guessing your handle's tab shape, a 14 mm deep forked jaw slides over the handle blade (1.5–3.6 mm thick) and pinches it with an M3×20 screw and a captured M3 nut; five 4 mm chain holes on a 12 mm pitch set the flapper chain length. Arm cross-section is 5 × 12 mm so the bending load runs along the print's strong axis.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A stackable closet-flange riser for when new tile or vinyl leaves the toilet flange below the finished floor and the wax ring won't seal. 164 mm OD ring with a 110 mm bore that clears a 4" DWV throat, obround bolt slots on the 139.7 mm (5.5") closet-bolt standard, four 4.5 mm screw holes for #8 anchors, and a 1.5 mm tongue/2.0 mm groove so rings interlock and stack in 6.4 mm (1/4") steps. Print in PETG or ABS at high infill and stack as many as the gap needs.
A 120 mm slide-on splint sleeve that repairs a snapped 11 mm tent pole section: 11.4 mm teardrop bore (0.4 mm slip fit), 4 mm walls, tapered lead-in mouths at both ends, and two M3 self-tapping set-screw bosses (2.6 mm holes) that pin it to each pole half so it can't migrate off the break. A centre notch in the full-length stiffening rib lines it up on the crack; overall 120 x 19.4 x 22 mm with a flat printed pad on the bottom. Print in PETG or ASA for UV and cold tolerance.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A 140 x 95 mm riser shelf that slides in around a bathroom sink drain so the dead space beside the P-trap becomes usable storage — the 52 mm wide U-slot (26 mm end radius) clears common 1-1/4 in and 1-1/2 in tubular tailpieces and their slip nuts. Four hollow 18 mm legs give 45 mm of clearance over the cabinet floor, 7 mm drain slots let a drip pass straight through instead of pooling under your bottles, and each foot has a 4.5 mm M4 clearance hole if you want to screw it down.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.