Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A split clamp for a 31.8 mm handlebar that carries a second 22.2 mm accessory bar stub 55 mm out to the side, so lights, a GPS, a bell and a phone mount stop fighting for stem space. Closed by two M5 bolts with captured nuts, 99 x 44 x 55 mm, gusseted web under the stub.
A print-in-place four-bar over-center toggle clamp (125 x 46 x 26 mm) that pushes a 24 mm wide pad sideways to lock a workpiece against a fence — handle, coupler, arm and base all print as one piece on printed pivot pins with 0.5 mm clearances. The base bolts down with two M5 clearance holes plus two 20 mm M5 slots so the clamp can be slid to the work on a T-track, 2020 rail or drilled bench top.
A one-piece dust-extraction adapter that joins a 2-1/2 in (63.5 mm) shop-vac hose to a 1-1/4 in (31.75 mm) power-tool dust port — a 64.0 mm socket with an internal 45° stop shoulder steps down through a tapered cone to a 31.4→30.6 mm friction spigot with a seating flange. 79 mm tall, 78 mm across the three grip ribs, with a 3.4 mm M4 self-tapping screw hole through one rib so the hose can be locked instead of pulling off mid-cut.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A cable-tie-on bottle cage mount for bikes with no braze-on bosses: a 26 x 26 x 90 mm block with a 90-degree V groove that self-centres on round tubes from about 22 to 32 mm, and two M5 cage bolt bores on the standard 64 mm boss spacing with captured 8 mm hex nuts loaded from the side. Two 8 x 2.8 mm tunnels take 4.8 mm standard or 7.6 mm heavy-duty zip ties that wrap the tube and pull the groove down onto it.
A three-piece print-in-place cam cleat that jams 4–8 mm rope or paracord one-way for tarps, roof racks, awnings and van-life tie-downs — pull to tension, lift the line out to release. Base is 76 x 54 x 16 mm with four 5.5 mm M5 clearance holes on a 60 x 42 mm rectangle; the two toothed cams ride on 6 mm printed pins with retaining heads and are closed by 1.2 mm curved flexure springs, with 4.5 mm guide ribs fairleading the line in.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A print-in-place hinged tilt bracket for small 10–100 W solar panels, 140 x 60 mm with a 5 mm base plate and a 60 mm-tall detent post. The base bolts to a roof rail, van rack or shed wall with four M5 lag screws (5.5 mm clearance holes) and the panel wing takes four M5 frame bolts; a single M5 x 60 bolt through the post and quadrant fin locks the tilt at 15°, 30°, 45° or 60°, with strap slots on both plates for frameless panels.
A 120 mm bench-top miter box with guided 90° and left/right 45° saw slots for cutting trim, dowels, and small stock by hand. The channel takes pieces up to 34 mm wide and about 20 mm thick, and two counterbored holes let you screw or clamp it to a bench.
A handheld drill guide with five tall bushing towers (3.2, 4.2, 5.2, 6.4 and 8.2 mm) that keep a bit perfectly perpendicular, plus a 90° V-groove underside that self-centers the holes on dowels and round stock. Block is 102 x 36 x 44 mm.
A palm-sized sanding block with a flat 88 x 68 mm face and a contoured grip; a quarter sheet of sandpaper wraps the bottom and tucks into the two tapered slots on the end shoulders, which wedge tighter as you sand. Hollow-cored so it stays light and cheap to print.
An 80 mm L-block that holds two boards at a true 90° while glue sets, with open windows so a spring clamp reaches straight through to the workpiece and a rounded corner relief for squeeze-out. Two 4.5 mm holes let you screw it down to a bench or assembly board.
A 90 mm V-jaw layout plate that drops over the end of any round bar, dowel or pipe from about 9 to 70 mm diameter; scribe through the long centre slot, rotate the stock 90° and scribe again — the crossing point is dead centre. The 8 mm deep V lips self-centre the tool so it can't rock off the end face.