Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A four-bay bench or wall caddy that stands RC LiPo packs upright, each bay 34 x 28 mm (fits packs up to about 33 x 27 mm in cross-section — the usual 2S/3S 1300–2600 mAh class) with a dedicated 10 mm rear channel per bay so the balance lead drops over a 36 mm divider wall and its plug hangs isolated from the neighbouring pack's main leads. Overall 148 x 47 x 52 mm, with a push-up window under each bay and two M4 clearance holes (4.5 mm) through the 4 mm back wall for wall mounting.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A 44 mm square block with four through-bores (18.7 mm, on 20.6 mm centres) that holds four 18650 cells upright, parallel and bottom-flush against the bench so nickel strip lands square during spot-welding or pack glue-up. Open-topped grab notches — one per cell, in 4-fold symmetry — let you spin a cell to set polarity, and two 5 mm ears with M3 clearance holes bolt the jig to the bench; overall 68 x 44 x 26 mm.
A weighted-footprint cup that parks a wood glue bottle nozzle-down so the glue is always primed and never crusts over. The tapered Ø27–35 mm bore self-centers most 8–16 oz caps, with a 12 mm drip well below the tip and two side slots for grip and level checking; 80 mm base, 60 mm tall.
A 147 mm staircase block that stands a 13-piece metric drill index upright, with bores from 1.5 mm to 7.5 mm rising left to right so the size order is obvious at a glance. Each step is taller than the last, so bit tips sit deep and shanks stay easy to grab.
A gravity-fed dual-channel dispenser that stacks 6 AA and 8 AAA cells and drops the next one into a front grab window with a retaining lip. Stands 92 mm tall on a shelf or screws to a wall through the two rear ears.
A weighted-footprint cradle that holds a closed laptop, tablet or notebook upright on the desk, with a 22 mm slot, chamfered lead-in edges and a cable pass-through slot in the floor. 90 × 70 × 50 mm.