Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A 114 x 114 mm plate that bolts to a monitor's VESA 75 x 75 or 100 x 100 M4 pattern (sandwiched under the arm/stand screws) and carries a 92 x 50 mm tray with 23 mm side walls and a 7 mm front rail behind the screen. A 62 mm centre window clears the arm head, twin 5 x 16 mm strap slots and a 10 mm cable pass-through hold a USB hub, dongle receiver, SSD or mini PC off the desk.
A four-link cable drag chain with an integrated M3 mounting foot, printed fully assembled — no pins, no clips, no post-assembly. Each 32 mm link carries an 11 mm wide x 13 mm tall cable channel and an arc-slot bend limiter that stops the chain dead straight and allows 35 deg of bend, so the top run won't sag. Overall 170 x 29 x 16 mm; the foot takes two M3 screws on a 19 mm spacing.
A 62 mm square, 19 mm tall adapter that lets a NEMA 17 stepper bolt into a machine face drilled for NEMA 23 — the base carries the 47.14 mm M5 pattern, the raised Ø52 tower carries the 31 mm M3 pattern with a 22.4 mm pilot register for the motor's centring boss. The hollow Ø30 core clears a shaft coupler, a 14 mm side window gives Allen-key access to the coupler set screw, and counterbores in the base bottom fully recess the four M3x20 motor screws so the adapter still seats flat.
A 140 x 95 mm riser shelf that slides in around a bathroom sink drain so the dead space beside the P-trap becomes usable storage — the 52 mm wide U-slot (26 mm end radius) clears common 1-1/4 in and 1-1/2 in tubular tailpieces and their slip nuts. Four hollow 18 mm legs give 45 mm of clearance over the cabinet floor, 7 mm drain slots let a drip pass straight through instead of pooling under your bottles, and each foot has a 4.5 mm M4 clearance hole if you want to screw it down.
A desk dock with a recessed tray sized for a standard 76 x 76 mm sticky note pad and a rounded rear trough for pens, pencils and erasers. A scalloped thumb notch in the front wall lets you peel notes one-handed; footprint is 86 x 113 mm and 20 mm tall.
A three-step cabinet riser that stair-steps spice jars so every label is visible from the front. 80 mm wide x 108 mm deep x 66 mm tall, with a 3 mm lip on each tread so jars can't slide off; hollow open-bottom shell with internal ribs to keep it light.
A 100 mm lazy-susan tray that prints as one piece and spins straight off the plate — the deck is captured by a mushroom post and rides on low-friction ring lands. Holds spice jars, sauces, pens or craft supplies in a 90 mm bowl with a 10 mm rim and eight grip ribs.
A 100 x 72 mm bar-soap dish with a 3 mm sloped floor, five lengthwise ribs that keep the bar up out of the water, and a spout notch with a flat drip tongue that sends runoff into the sink instead of onto the counter.
A shelf that hangs on the center screw of a standard duplex outlet cover to hold a charging phone off the floor. 70 mm wide plate, 58 mm deep ledge with an 8 mm lip and a cord notch through the middle.
A two-compartment caddy that sits beside the faucet to hold a sponge and scrub brush separately, with slotted drain holes in the bottom so water runs out instead of pooling. Fits a standard sponge; overall footprint 100 x 70 x 45 mm.