Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A bench-top fume extractor housing for any 40 x 40 x 10 mm fan — the fan bolts to the 60°-tilted face on its standard 32 mm M3 pattern (3.4 mm clearance holes with counterbores so the heads sit flush), and a 42 mm square of activated-carbon filter sheet press-fits into the 41.5 x 41.5 x 4 mm pocket in front of a ribbed finger-guard throat. Footprint 52 x 64 mm, 50 mm tall, with two M4 holes in the weighted base for bolting it to the bench and an open rear duct so exhaust clears the work.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A print-in-place PCB soldering vise: a 110 x 38 x 8 mm base rail with a captive T-slot jaw that slides along it, holding boards from 15 mm to 79 mm wide in a pair of 2.6 mm edge grooves (sized for 1.6 mm FR4). An M4 self-tapping screw through the sliding jaw jacks against the rail floor to lock it; four 4.5 mm M4 clearance holes bolt the rail to a bench or plate.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A 115 x 70 mm bench caddy for a soldering station: twin V-yokes cradle the iron by its handle (notch accepts 8–24 mm grips) at a 25° tip-up angle so the hot tip hangs ~90 mm clear in free air, never touching plastic. Includes a 41 mm ID x 30 mm deep brass-wool cup, four 6.5 mm spare-tip holes plus an 11 mm flux-pen pocket, a 9 mm snap-in cable keeper for the iron lead, and two M4 clearance holes to bolt it to the bench. Print in PETG if your iron runs hot.
A 140 x 85 x 16 mm bench tray with six sloped-floor bins — four 32 x 30 mm pockets for M2/M2.5/M3/M4 screws, nuts and washers, plus two full-length 32 x 62 mm bins for nylon standoffs and longer screws. The front ledge is a screw gauge: four through-holes (2.4 / 3.4 / 4.5 / 5.5 mm) let you drop an unknown fastener through and read off M2, M3, M4 or M5, and every bin floor rises 4 mm toward the back so parts collect at the near edge instead of hiding in a corner.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A 95 x 70 mm catch-all tray with two compartments for keys and coins plus an upright slot that stands a phone (up to 13 mm thick with case) face-up on a raised shelf. A tunnel through the back wall feeds the charging cable up to the phone's port so the cord never leaves the dock.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.