Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
Replacement bottom guide for a bypass/sliding shower door: a 46 x 22 x 15 mm block that screws to the track with two countersunk M3 (#6) screws and carries the door's bottom glass edge in a 7.2 mm channel sized for 1/4 in (6.35 mm) glass. A V-shaped lead-in opens the channel to 12.7 mm at the rim so 5/16 in and 3/8 in glass still ride about 5 mm deep, and flared ends in plan view guide a drifting door back in; the counterbored screw holes also drain the channel.
Replacement wall-end bracket for a broken towel bar, with a stepped socket that takes both 1 in (25.4 mm) and 3/4 in (19 mm) tube — a 1 in bar bottoms on the step after 18 mm, a 3/4 in bar slides 28 mm deep — and an M4 set screw that locks it so you don't have to replace the whole rail set. Back plate is 42 x 68 x 6 mm with two counterbored 4.5 mm holes 52 mm apart for #8/M4 anchors, bar centre stands 38 mm off the wall, overall 55 mm tall.
A 120 mm replacement flush lever arm for a toilet tank, for when the brittle OEM arm snaps at the chain hole and the linkage isn't sold separately. Instead of guessing your handle's tab shape, a 14 mm deep forked jaw slides over the handle blade (1.5–3.6 mm thick) and pinches it with an M3×20 screw and a captured M3 nut; five 4 mm chain holes on a 12 mm pitch set the flapper chain length. Arm cross-section is 5 × 12 mm so the bending load runs along the print's strong axis.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A 120 mm slide-on splint sleeve that repairs a snapped 11 mm tent pole section: 11.4 mm teardrop bore (0.4 mm slip fit), 4 mm walls, tapered lead-in mouths at both ends, and two M3 self-tapping set-screw bosses (2.6 mm holes) that pin it to each pole half so it can't migrate off the break. A centre notch in the full-length stiffening rib lines it up on the crack; overall 120 x 19.4 x 22 mm with a flat printed pad on the bottom. Print in PETG or ASA for UV and cold tolerance.
A standoff bridge that suspends a 40 mm fan directly over a Raspberry Pi 4B / 3B+, with a 32 mm shrouded duct collar aiming the air at the SoC instead of letting it spill sideways. 74 x 64 mm plate on four 18 mm legs that clear the USB/Ethernet stack, 58 x 49 mm M2.5 board pattern with captured nuts at the board end, 32 mm square M3 fan pattern, plus side exhaust vents and a 26 x 4.5 mm slot for GPIO ribbon or camera flex.
A stackable 96 x 84 x 28 mm deck for Raspberry Pi 4B / 3B+ cluster builds: each board bolts to four 6 mm standoffs on the verified 58 x 49 mm pattern with 2.9 mm holes for M2.5 screws, and the 14 mm corner posts peg into the socket of the deck above for a 28 mm stack pitch (16 mm of free air over each board for a HAT or fan). Three large windows give vertical airflow, plus two 4 mm cable-tie slots and two M3 clearance holes so the bottom deck can be screwed to a wall or panel.
A 110 x 62 mm vented backplate for a Raspberry Pi 4B / 3B+ with four 5 mm standoffs on the 58 x 49 mm bolt pattern (2.9 mm bores for M2.5 screws), edge stiffening ribs, two keyhole slots that drop over #8 wall screws, an M4 lock hole at the bottom, and a zip-tie bridge for power-cable strain relief. Five long vent slots keep air moving under the board and cut print time.
A ground stake with a tapered funnel socket that grips 12 oz cans, bottles and tapered party cups so drinks stay upright in sand, grass or dirt. 148 mm tall with four grip ribs at the rim for pushing it in by hand.