Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Solar Path Light Rescue Stake
A replacement ground stake for solar path lights that snapped at the thin stake joint. The 170 mm stake has a T-ribbed spike and a 90° V-cradle on top that holds any light pole from 12 to 25 mm in diameter, fixed with two zip ties through bridged slots. It prints flat so the spike's layer lines run along its length, which stops it snapping at the ground line.
Twin-Band Downspout Wall Standoff
This is a wall-mounted standoff block for a gutter downspout. It measures 130 x 60 x 11 mm and screws on with two #10 or M5 screws (5.5 mm countersunk holes). Two 14 x 3.5 mm tunnels run through it for zip ties or 1/2 in (12.7 mm) worm-drive hose-clamp bands. The band wraps around the downspout, so one part fits 2x3 in (about 51 x 76 mm nominal), 3x4 in or any other profile, and it replaces the brittle vinyl straps that snap every winter.
Split Loom V-Saddle Screw Mount
A one-size screw-down saddle for routing split-loom wire harnesses. Its 90° V-cradle is 20 mm wide and 10 mm deep and centres any loom from 6 to 25 mm OD. Two 5.5 x 2.4 mm tunnels under the cradle take zip ties to strap the loom down, so you don't need a multi-pack of P-clips to get the one size you want. The footprint is 60 x 40 x 16.5 mm. The two 4.5 mm holes on 44 mm centres take #8 wood screws (4.2 mm shank) or M4 bolts, for car, boat, garage or control-panel wiring.
Flagged: lifting or tensioned load. Not for safety-critical use without independent engineering review.
Snowblower Chute Crank Rod Guide
This replaces the snapped eyelet that holds a snowblower's chute-rotation crank rod against the handle. A 90° V-saddle sits on any 19–32 mm handle tube and is held by two zip ties (up to 5 mm wide) that run through tunnels in the saddle. The 14 mm guide eye takes crank rods up to 12 mm, about 38 mm from the tube. Overall size is 40 x 66 x 24 mm. Print it in PETG for winter use.
N20 Gearmotor Zip-Tie V-Cradle Mount
A 48 x 34 x 20 mm chassis mount for micro metal gearmotors (N20/N30, 12 mm round can): a 90° V-cradle self-centres any can from about 10 to 14 mm diameter and two 4.5 x 2.4 mm tunnels take zip ties straight over the motor, so it needs no motor-specific bolt pattern. A 6 mm solid rear thrust wall stops the motor being pushed back by wheel side load, and the 4 mm base has four 3.4 mm M3 slots (11 mm of travel, on 30 x 25 mm centres) plus one round 3.4 mm M3 hole for a located third point.
Strap-On Desk Leg Cable Spine
A 119 x 60 x 21 mm snap-in cable raceway segment that straps to a desk or sit-stand leg and carries the cable bundle vertically: a 26 mm wide x 16 mm deep channel with lips narrowing the mouth to 18 mm so cables push in and stay put. Mounts with velcro or zip ties through two 18 x 4.4 mm wing slots (fits any leg profile) or two 4.5 mm screw holes (M4 / #8 wood screw, 4.2 mm shank), and each segment lap-joints into the next with a 9 mm tongue and 4 mm locating peg so you stack as many as the leg is tall.
Under-Sink Inline Water Filter Bracket
A wall/cabinet bracket that holds a standard 2 in inline water filter (fridge ice-maker, RO post-filter, whole-line carbon) off the plumbing instead of letting it hang on the tubing and kink the push-fits. Twin 90° V-block saddles self-centre any 45–56 mm filter body and a 4.8 mm zip tie through each saddle straps it down; snap-in end clips route 1/4 in (6.35 mm) OD tubing, and four 4.5 mm holes take #8 wood or M4 screws. 130 × 48 × 34 mm, prints flat with no supports.
Zip-Tie Faucet Spout Extender
A catch-and-channel trough that hangs on a bathroom faucet spout (16–28 mm tip, held by two 4.8 mm zip ties through the jaw slots) and throws the stream about 70 mm forward, so small kids can reach the water and tall bottles fill without hitting the spout. 100 x 40 x 40 mm, self-centering 60° V jaws, 3 mm walls and a sloped 2.5–4.5 mm floor that drains instead of puddling; print in PETG if the tap runs hot.
Cable Tie Length Sorting Caddy
A five-bay stair-stepped caddy that keeps zip ties sorted by length (roughly 100 / 150 / 200 / 250 / 300 mm) instead of tangled in one bag — bay widths run 14 to 20 mm, each with a front window so you can pinch one tie out single-handed. Footprint is 100 x 26 mm with bay walls 30 to 46 mm tall; it stands on the bench or screws to a wall through two 4.5 mm M4 clearance holes in the 4.5 mm back wall, driven from inside bays 2 and 4.
Under-Desk Power Strip Cradle
A screw-up bracket that lifts a power strip (or a laptop brick) off the floor and onto the underside of a desk or bench: two 15° V-arms self-centre any body 38–52 mm wide, and a 4.8 mm zip tie cinches it down through four slots, its loop hidden in a 2.2 mm groove milled into the desk-facing side so the plate still sits flat. 68 x 32 mm footprint, 31 mm tall, two 4.5 mm counterbored holes on 26 mm centres for M4 or #8 screws. Print two and space them along the strip.
Flagged: mains electrical wiring. Not for safety-critical use without independent engineering review.
Seatstay Clamp Wheel Truing Gauge
A truing gauge that zip-ties to a seatstay or fork blade (12–28 mm round tube sits in the 90° V-cradle) so any bike becomes a truing stand — the 34 mm yoke gap straddles rims up to ~30 mm wide and five M3 screws running in 4.0 mm heat-set inserts act as adjustable feelers: four lateral (two per prong, 20 mm apart radially, so you can land one on the rim sidewall wherever you clamp) and one facing radially outward for hop. 104 x 52 x 12 mm, prints flat with no supports.
Garage Door Safety Eye Bracket
A replacement mounting bracket for garage door opener safety photo eyes, for when the original snapped or never fit your track. The 38 x 100 x 5 mm plate screws to the vertical door track with #8 self-tappers through four 4.5 mm holes plus two 4.5 x 22 mm height-adjustment slots; the 46 mm sensor wall takes any eye with two zip ties through the 7 x 3.5 mm slots or an M4 heat-set insert, and the angled hood shades the lens from low sun that causes phantom reversals.
Relay And Fuse Zip-Tie Mount Base
A 106 x 52 x 6 mm mounting base (142 mm overall with the screw feet) that gives automotive relay sockets and inline fuse holders something to bolt to instead of dangling off the loom. Two 33 mm bays between 3 mm divider ribs take 4- and 5-pin relay sockets, a 45 degree V-saddle bay cradles round inline fuse holders from roughly 8 to 16 mm, each bay has a pair of 8 x 3.2 mm slots plus a recessed underside channel so a 4.8 mm zip tie loops over the part without lifting the base off the panel, and the two ears carry 4.5 mm M4 clearance holes for firewall or bulkhead screws.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.