Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Cone-Seat Kitchen Sink Strainer Basket
A drop-in sink strainer basket that replaces a cracked or rusted basket in a standard 3.5 in (about 90 mm) kitchen sink drain. It has no fixed diameter to match: a 45° conical seat centres it in any drain opening from 72 to 108 mm across. The basket is 108 mm across and 46.5 mm tall. It has 12 radial floor slots, 16 wall slots and a 16 mm lift knob, and sits about 36 mm deep in a 90 mm opening.
32 To 35 mm Vacuum Wand Adapter
Fits a 32 mm vacuum wand to a 35 mm attachment. Both ends are tapered friction fits, so small differences between brands (Shark, Bissell, Hoover, Dyson-style) still seal. The socket tapers from 33.2 to 31.4 mm ID and takes a 32 mm male wand, stopping on an internal shoulder. The male spigot tapers from 35.8 to 34.0 mm OD and plugs into 35 mm tool sockets. The part is 85 mm long with a ribbed grip collar.
Storm Door Insert Two-Reach Turn Button
A replacement turn button for the swing clips that hold glass or screen inserts in aluminum storm doors and windows. It is 56 x 16 mm and pivots on a #6/#8 or M4 screw through a countersunk 4.5 mm hole. The two arms reach different depths, 2 mm and 5 mm above the frame face. Turn whichever arm matches your insert onto the panel, and the chamfered edges ride up onto the panel as you turn it. No discontinued OEM clip is needed.
Wheelbarrow Tub Support Wedge Block
A replacement for the plastic wedge that sits between a wheelbarrow tub and its handle rail. It is 90 x 40 mm and tapers from 18 to 38 mm tall (a 12.5° pitch). Underneath is a 26 mm wide 90° V-saddle that seats on round steel handle tubes about 25–40 mm across or on the edges of a wooden rail. The through-slot is 6.8 x 20.8 mm, so a 1/4 in or M6 tub bolt lines up even when the original hole spacing varies. The ribbed top has open pockets to save material.
Bolt-On Ladder Rail Foot Cap
Replacement foot cap for aluminium step and extension ladders with 40 x 20 mm rectangular leg tubing — it slips over the rail end (40.6 x 20.6 mm socket, 27 mm deep) and is held by an M5 bolt through the rail instead of glue, with two 5.5 mm hole heights (14 mm and 24 mm above the ground) so you can reuse the original rivet hole. The 52 x 32 x 7 mm pad has 3 mm deep tread grooves and a 5 mm centre drain, total height 34 mm.
Step Can Pedal Rocker Arm
Replacement rocker/bell-crank arm for the foot-pedal linkage in a step trash can (Simplehuman-style 30 L round cans and their clones), the one plastic lever that always snaps and that nobody sells as a service part. 98.7 mm long with a 5.5 mm pivot bore for a 5 mm pin or M5 bolt, two 4.5 mm pedal-rod holes 9 mm apart to re-tune pedal throw, and an open C-socket at the lift end that clips over a 4 mm lid rod; 10 mm tall bosses and a full-length spine rib carry the load in the print plane. Measure your can's pivot pin before printing — holes are sized to standard 4 mm / 5 mm pins.
Handheld Bidet Sprayer Wall Cradle
A screw-on replacement cradle for the cheap handheld bidet sprayers whose thin plastic holder snaps off the wall — you can't buy the cradle alone, only the whole kit. The 50 x 100 mm backplate takes three counterbored M4 screws (two at the top, one at the bottom) so it can hit fresh anchors instead of the wallowed-out original holes, and two gusseted shelves with tapered snap-past-lip slots cradle any sprayer neck from 16 to 22 mm and barrel from 20 to 26 mm; it stands 36 mm off the wall.
Sous Vide Circulator Rim Clamp
Replacement pot clamp for a sous vide circulator whose OEM plastic clamp has snapped — a 38 x 80 x 46 mm C-clamp that hooks over any pot wall or Cambro/Rubbermaid tub rim up to 18 mm thick and locks down with an M4 thumbscrew running in a 5.5 mm heat-set insert bore. A 90° V-channel cradles any circulator barrel from 40 to 70 mm diameter and two 9 x 4 mm slots take a zip tie or velcro strap to bind the barrel into the V. The C-profile lies in the bed plane so the clamping load runs along the layer lines, not across them.
Sliding Shower Door Bottom Guide
Replacement bottom guide for a bypass/sliding shower door: a 46 x 22 x 15 mm block that screws to the track with two countersunk M3 (#6) screws and carries the door's bottom glass edge in a 7.2 mm channel sized for 1/4 in (6.35 mm) glass. A V-shaped lead-in opens the channel to 12.7 mm at the rim so 5/16 in and 3/8 in glass still ride about 5 mm deep, and flared ends in plan view guide a drifting door back in; the counterbored screw holes also drain the channel.