Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Table Leaf Alignment Pin And Socket Set
Two press-in alignment pins and two flanged sockets that keep extension-table, drop-leaf and two-piece desk leaves level. Drill both edges to 12 mm. The pin shanks and socket sleeves have crush ribs (12.5 mm across the ribs) that grip the wood. Each 8.2 mm nose slides into an 8.8 mm socket bore that has a chamfered lead-in. The parts print on a breakaway sprue, and the set replaces the plastic leaf pins that hardware stores no longer stock.
Slotted Desktop Seam Joining Plate
A ribbed plate, 160 x 70 x 11 mm, that screws to the underside of two desktops butted together (for an L-desk, a bench extension, or a split top) and keeps them flush. It has eight 5.0 mm slots, 14 mm long, for #8 (4.2 mm) wood screws with washers. The slots let you pull the tops tight before you snug the screws down. A V-notch marks the centre line so you can line it up on the seam. Three 7 mm tall ribs run across the seam to resist sag.
Desk Leg M5 Bolt Leveling Foot
A 50 x 50 mm plate that screws under a wooden desk or table leg with four #8 screws (4.8 mm countersunk holes) and turns any M5 bolt into a leveling foot. An 8 mm M5 hex nut drops into a pocket on the face against the leg, so the floor load goes through the bolt and nut into the wood, not the plastic. The 16 mm gusseted boss guides the bolt through a 5.5 mm bore. Turn the bolt head to level a wobbly desk, then lock it with a second nut.
Hairpin Desk Leg Stripped-Screw Repair Plate
Fixes a hairpin or plate-mount desk leg whose wood screws have stripped out of the tabletop. The 110 x 110 x 7 mm plate goes on fresh wood with eight #8 wood screws (4.8 mm holes) set on tabs 144 mm across, clear of the old holes. The leg's steel plate then bolts on with M4 bolts and nuts that slide in four diagonal nut tracks (7.4 mm wide), so any hole pattern from about 3 in to 4.5 in square fits.
Drop-Front Desk Lid Folding Stay
This print-in-place two-link folding stay replaces the snapped friction support on a drop-front secretary desk, a hinged school-desk lid or a blanket chest. It prints as one assembly of four pieces joined by three 5 mm pins with 0.5 mm running clearance. Pivot to pivot it reaches 144 mm when straight, and the load runs along the links in the layer plane. A flat 36 × 24 mm plate screws to the cabinet side and a gusseted 24 × 28 mm L-bracket screws to the lid. Both take #6 wood screws (3.5 mm shank) through 4.0 mm clearance holes: the side plate has countersinks, and the lid bracket needs pan-head screws.
Swing-Tab Desk Drawer Pull-Out Stop
A 70 x 20 x 6 mm tab that stops a drawer falling out. It screws to the inside of the drawer back with a pivot screw and a lock screw, and the tip rises above the back to catch the desk's front rail. To pull the drawer out, remove the lock screw and swing the tab down. It's a stand-in for lost stoppers like IKEA Rast part 102323. Both holes are 4.5 mm with countersinks, so they take #6 (3.5 mm) or #8 (4.2 mm) wood screws or M4 screws.
Straddle Cam Lock Desk Repair Bracket
This inside-corner bracket is 80 mm long with 36 mm legs. It repairs flat-pack desk joints where the cam lock has stripped or torn out. A 24 x 14 mm window at the centre fits over the old cam housing and any crumbled chipboard. Four slotted #8 wood-screw holes (4.8 mm wide with 9 mm counterbores) sit 26 mm from the corner so the screws go into undamaged wood, and 6 mm end gussets keep the joint square.
Flat-Pack Desk Anti-Wobble Corner Brace
A 70 x 70 x 36 mm gusseted L-brace that screws into the inside corner where a flat-pack desk top meets its side panel. It stiffens the joint once the cam locks work loose and the desk starts to rack. Each 5 mm leg has two 4.8 x 8 mm slots that take #8 (4.2 mm) or #10 (4.8 mm) pan-head wood screws, so you can line it up without new pilot holes. Use 5/8 in screws in 16–18 mm particleboard.