Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Hanging Graduated Tool Shelf
A 100 x 60 mm L-shaped tool shelf, part of the 'Printed French Cleat Bin Wall' kit. It bolts to one Cleat Bin Hanger Bracket with two M3x12 socket head cap screws, which pass through 3.4 mm holes at 15 and 45 mm on its 4 mm back plate and thread into the hanger's captured M3 nuts. The 6 mm deck has seven 9 mm screwdriver and awl holes at 12 mm pitch and five 14 mm plier and marker holes at 20 mm pitch. Two 5 mm gussets brace the deck.
Slide-In Cleat Bin Divider
A removable compartment divider for the 'Printed French Cleat Bin Wall' kit. It is a flat plate 94.7 x 38 x 2.0 mm and drops into the 2.8 mm wall grooves of either the Small Scoop or the Wide Twin-Hanger bin. No screws or other hardware are needed. It has 0.4 mm of clearance at each end and on each face, a 20 x 10 mm semicircular finger notch for pulling it out, and 0.8 mm lead-in chamfers on the bottom corners.
Wide Twin-Hanger Cleat Bin
This wide open-top scoop bin is part of the 'Printed French Cleat Bin Wall' kit. It measures 160 x 100 mm and is 70 mm tall at the back, sloping to 40 mm at the front. It bolts to two Cleat Bin Hanger Brackets set 80 mm apart with four M3x12 socket head cap screws, which pass through 3.4 mm rear-wall holes at x = ±40 mm and z = 15/45 mm and thread into the hangers' captured M3 nuts. Three 2.8 mm grooves at x = −26, 0 and +26 mm take the kit's slide-in dividers, and the front has a 100 x 14 mm label recess.
Small Scoop Cleat Wall Bin
An open-top scoop parts bin for the 'Printed French Cleat Bin Wall' kit. It measures 80 wide x 100 deep x 70 mm tall at the back, sloping to 40 mm at the front. It bolts to one Cleat Bin Hanger Bracket with two M3x12 socket head cap screws, which pass through 3.4 mm holes spaced 30 mm apart and thread into the hanger's captured M3 hex nuts. Inside are two divider grooves 2.8 mm wide at ±12.5 mm for the kit's slide-in dividers, and the front has a 50 x 14 mm label recess.
Cleat Bin Hanger Bracket
This universal hanger is part of the 'Printed French Cleat Bin Wall' kit. It is 40 mm wide, 115 mm tall and 21 mm deep. Its 45° tongue hooks over the printed cleat rail with 0.5 mm of clearance and lifts off when raised 12 mm. A foot at the bottom bears on the wall. Every kit bin and the tool shelf bolts to its flat front face with two M3x12 socket head cap screws, through 3.4 mm holes spaced 30 mm apart vertically. The screws thread into M3 hex nuts captured in 5.7 mm pockets on the back of the web.
Pinned Cleat Rail End Stop
End stop for the 'Printed French Cleat Bin Wall' kit. It is a 20 x 55 x 13 mm block that butts against the end of a 200 mm cleat rail and sits 10 mm above the rail's 45 mm front and 8 mm in front of it, so hangers can't slide off the end. It takes two 4 mm x 20 mm steel dowel pins in 4.3 mm x 11 mm blind holes at d=6, h=10/25, which you can glue with CA. The block is symmetric, so turn it over to use it at the other end of the row.
Printed 45 Degree Cleat Rail
A 200 mm long French-cleat wall rail for the 'Printed French Cleat Bin Wall' kit. It is 12 mm thick and 45 mm tall, with a 45° bevel that the kit's hanger brackets hook onto. It takes three #8 wood screws (4.2 mm shank) through 5.0 x 10 mm slots, with a 10.5 x 15.5 x 4 mm counterbore for the head. Each end has two blind holes 4.3 mm across and 11 mm deep, which take 4 x 20 mm steel pins to join rails end to end. It prints flat on its wall face with no supports.