Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Window Rescreening Spline Gauge Parts Tray
A 160 x 100 x 18 mm bench tray for rescreening window screens. It has a 75 x 55 mm well for a coil of spline, four 36 x 26 mm cups to keep corner keys sorted by profile, and a 154 x 32 mm trough for the roller tool head and blades. The front wall has six spline sizing holes. They step from 0.125 in (3.2 mm) to 0.220 in (5.6 mm), so you can identify old spline before you go to the store.
Five-Peg Compression Spring Sort Tray
A 150 x 80 mm tray for a loose spring assortment. Five 50 mm pegs at 4, 5, 6, 8 and 10 mm diameter hold compression springs stacked by inner diameter, and each peg doubles as an ID gauge: a spring goes on the largest peg it will slide over. The pegs sit in walled cells marked with 1 to 5 floor dots, and a full-width back trough holds extension and torsion springs.
Trim Clip Hole-Gauge Sort Tray
A 152 x 78 x 30 mm tray with six bays for automotive push-pin trim clips. Each bay has its own test hole in a 2.4 mm ledge that stands in for the panel: 6, 7, 8, 9, 10 and 11 mm, each modelled 0.2 mm oversize. Push a loose or salvaged clip into the holes until it snaps home and you know which bay it goes in and which panel hole it fits. The clip's legs drop into a hidden bridged channel under the ledge, so a clip bought in a mixed variety pack gets sorted by hole size.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
O-Ring ID Sizing Peg Tray
A 150 x 72 mm lipped bench tray with ten chamfered sizing pegs from 5 to 22 mm diameter. The front row is 5, 6, 8, 10 and 12 mm, left to right, and the back row is 14, 16, 18, 20 and 22 mm. Tip a mixed bag of unlabeled O-rings, grommets or seals into the tray. Slide each ring down the largest peg it fits snugly and stack it there, so every stack is sorted by inside diameter and you can find the size without a caliper.
E-Clip Groove Gauge Sort Tray
A 156 x 64 x 27 mm tray with seven compartments for E-clips. Six of them have a gauge post on the back wall, sized 4, 5, 6, 7, 8 and 9 mm. E-clips are sized by groove diameter, so you snap a mystery clip onto the post it grips snugly and drop it in the bin in front of that post. The seventh bin holds small or odd clips, and a 45° ramp at the front of each bin lets you slide a single clip out with a fingertip.
Hex Standoff Length Gauge Rack
A 124 x 28 x 28 mm staircase rack that sorts AND measures female-female hex standoffs: eight columns with pockets at 5, 6, 8, 10, 12, 15, 20 and 25 mm, all pocket floors on one plane so a standoff sitting flush with the rim is that length, proud is longer, sunk is shorter. Front lane bores are 7.0 mm (M2.5/M3 hex at 5.0-5.5 mm across flats, plus round spacers), rear lane 8.6 mm (M4 hex at 7 mm across flats), with 5 mm scale grooves down both sides and two 3.4 mm M3 clearance holes to screw it to a shelf or bench.