Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Pegboard Driver And Plier Bar
A 126.2 W x 50 D x 60 H tool bar for standard 1/4 in pegboard (6.35 mm holes on a 25.4 mm grid), part of the '1/4 in Pegboard Locking-Peg Tool Wall' kit. It has six chamfered drop-through holes (8, 10 and 12 mm, for screwdriver shafts up to about 7, 9 and 11 mm) and two 10 x 28 mm plier slots. It hangs on two of the kit's printed octagonal hook pegs at X ±50.8 mm and is locked by two split, ridged lock pins 25.4 mm lower, through 5.8 mm octagon sockets in the 5 mm back plate.
Lipped Pegboard Hang Shelf
A 126.2 W x 100 D x 55 H shelf with a 4 mm deck, a 12 mm retaining lip at the front and two 4 mm side gussets. It is part of the '1/4 in Pegboard Locking-Peg Tool Wall' kit and fits standard 1/4 in pegboard (6.35 mm holes on a 25.4 mm grid, board 3.2–6.35 mm thick). It hangs on two of the kit's printed octagonal hook pegs at X ±50.8 mm and is locked by two split, ridged lock pins 25.4 mm below them, so it can't lift off or wobble. The 5 mm back plate has 5.8 mm octagon sockets, and three 6 x 60 mm drain slots keep the deck light.
Slide-In Wide Bin Divider
A flat 73.6 x 50 x 2.0 mm divider for the Divided Wide Pegboard Bin, part of the '1/4 in Pegboard Locking-Peg Tool Wall' kit. It slides into the bin's 2.9 mm wide x 1.5 mm deep grooves at X = -25.4, 0 and +25.4, leaving 0.45 mm clearance per side and 0.4 mm at each end. The bin hangs from standard 1/4 in pegboard (6.35 mm holes on a 25.4 mm grid). A 24 mm finger notch lets you lift the divider out, and 1.5 mm chamfered bottom corners help it drop into the grooves.
Divided Wide Pegboard Bin
A four-column open-top bin for standard 1/4 in pegboard (6.35 mm holes on a 25.4 mm grid), 100.8 W x 80 D x 70 H. It is part of the '1/4 in Pegboard Locking-Peg Tool Wall' kit. It hangs on two of the kit's printed octagonal hook pegs at X ±38.1 mm and is held by two split, ridged lock pins placed 25.4 mm below the hooks. The 5 mm back plate is flat behind, and the back plate and 3.6 mm front wall carry 2.9 x 1.5 mm grooves at X = −25.4, 0 and +25.4 for the kit's 2.0 mm slide-in dividers.
Locking-Peg Pegboard Small Bin
A two-column open-top parts bin, 50.0 W x 65 D x 70 H, that is part of the '1/4 in Pegboard Locking-Peg Tool Wall' kit. It hangs on two of the kit's printed octagonal hook pegs and is held by two split, ridged lock pins in standard 1/4 in pegboard (6.35 mm holes on a 25.4 mm grid). The 5 mm back plate has 5.8 mm octagon sockets at X ±12.7 mm, with the hook row at Z 62 and the lock row 25.4 mm below it, so a bump won't lift the bin off the board.
Hook And Lock Pin Sprue
Part of the '1/4 in Pegboard Locking-Peg Tool Wall' kit: one flat, 5.2 mm tall breakaway sprue with 4 L-shaped hook pegs and 4 split lock pins with ridges. They fit standard 1/4 in pegboard (6.35 mm holes on a 25.4 mm grid, board 3.2–6.35 mm thick). The octagonal pegs leave about 0.2 mm clearance per side in the hole. The two-prong pins have 6.8 mm across their ridges, so they grip the hole and keep bins and racks from lifting off the hooks. The sprue is 96 x 38 mm and every part snaps off a 3 mm runner.
Label-Window Drawer Pull
A finger pull and slide-in label holder, part of the '2020 Gridfinity Drawer Tower' kit. It has a 124 x 36 x 4 mm backplate and a 16 mm deep tapered lip. Two M3x14 screws go through its 3.4 mm holes at ±55 mm and the Drawer Front Panel and into the tray's self-tap pilots, so your pull lands on the tray. An 84 x 14 mm window shows an 86 x 18 mm card up to 0.8 mm thick, which slides into a 1 mm back slot that is open at the top.
Drawer Front Panel
Part of the '2020 Gridfinity Drawer Tower' kit. This 192.5 x 50 x 6 mm drawer face covers the 131.5 mm Gridfinity tray and both front 2020 posts. When you push the drawer in, the panel stops against the post fronts, so the impact goes into the frame and not the screws. Mount it with two M3x14 screws that pass through the pull, then through 3.4 mm holes at ±55 mm, then into the tray's self-tap pilots. A 1.5 mm locating rim on the back holds the panel square on the tray, and gaps in the rim clear the runner ends.
Gridfinity 3x3 Drawer Tray
This open-top drawer is part of the '2020 Gridfinity Drawer Tower' kit. Outside it measures 131.5 x 135 x 45 mm, and the 126.5 x 126.5 x 42.6 mm interior takes a 3x3 Gridfinity baseplate or 41.5 mm bins. The tray slides on the kit's twin-detent runners with 0.5 mm of clearance per side. Four 7 x 1.2 mm floor notches click over the runner ridges, and two 2.6 mm M3 self-tap pilots in the 6 mm front wall hold the front panel and pull with M3x14 screws.
Twin-Detent Drawer Runner
Part of the '2020 Gridfinity Drawer Tower' kit. This 135 x 20 x 16 mm side rail bolts to the inner slots of a front and a back 2020 post with two M5x10 socket-head screws and drop-in T-nuts. The 5.5 mm holes sit 115 mm apart and have 10 x 5.5 mm counterbores, so the heads end up below the face. A 6 x 5 mm ledge carries one side of a Gridfinity tray. Two 0.8 mm half-round ridges click into the tray's notches. The ledge ends have 1.5 mm lead-in chamfers. The part is symmetric, so all 8 runners are identical.
Tower Frame End Plate
Part of the '2020 Gridfinity Drawer Tower' kit: a 198.5 x 141 x 6 mm frame plate that holds four 2020 aluminium extrusion posts. It uses the same part at the base and, flipped, as the top cap. Each post sits in a 20.4 mm U-socket, 20 mm deep and open on the front or back so the drawer fronts can pass. Each socket takes three M5x8 screws into drop-in T-nuts through 5.5 mm holes. Four 4.6 mm holes take #8 wood screws, and the 39.25 mm side bars act as the top drawer's hold-down.
Hanging Graduated Tool Shelf
A 100 x 60 mm L-shaped tool shelf, part of the 'Printed French Cleat Bin Wall' kit. It bolts to one Cleat Bin Hanger Bracket with two M3x12 socket head cap screws, which pass through 3.4 mm holes at 15 and 45 mm on its 4 mm back plate and thread into the hanger's captured M3 nuts. The 6 mm deck has seven 9 mm screwdriver and awl holes at 12 mm pitch and five 14 mm plier and marker holes at 20 mm pitch. Two 5 mm gussets brace the deck.
Slide-In Cleat Bin Divider
A removable compartment divider for the 'Printed French Cleat Bin Wall' kit. It is a flat plate 94.7 x 38 x 2.0 mm and drops into the 2.8 mm wall grooves of either the Small Scoop or the Wide Twin-Hanger bin. No screws or other hardware are needed. It has 0.4 mm of clearance at each end and on each face, a 20 x 10 mm semicircular finger notch for pulling it out, and 0.8 mm lead-in chamfers on the bottom corners.
Wide Twin-Hanger Cleat Bin
This wide open-top scoop bin is part of the 'Printed French Cleat Bin Wall' kit. It measures 160 x 100 mm and is 70 mm tall at the back, sloping to 40 mm at the front. It bolts to two Cleat Bin Hanger Brackets set 80 mm apart with four M3x12 socket head cap screws, which pass through 3.4 mm rear-wall holes at x = ±40 mm and z = 15/45 mm and thread into the hangers' captured M3 nuts. Three 2.8 mm grooves at x = −26, 0 and +26 mm take the kit's slide-in dividers, and the front has a 100 x 14 mm label recess.
Small Scoop Cleat Wall Bin
An open-top scoop parts bin for the 'Printed French Cleat Bin Wall' kit. It measures 80 wide x 100 deep x 70 mm tall at the back, sloping to 40 mm at the front. It bolts to one Cleat Bin Hanger Bracket with two M3x12 socket head cap screws, which pass through 3.4 mm holes spaced 30 mm apart and thread into the hanger's captured M3 hex nuts. Inside are two divider grooves 2.8 mm wide at ±12.5 mm for the kit's slide-in dividers, and the front has a 50 x 14 mm label recess.
Cleat Bin Hanger Bracket
This universal hanger is part of the 'Printed French Cleat Bin Wall' kit. It is 40 mm wide, 115 mm tall and 21 mm deep. Its 45° tongue hooks over the printed cleat rail with 0.5 mm of clearance and lifts off when raised 12 mm. A foot at the bottom bears on the wall. Every kit bin and the tool shelf bolts to its flat front face with two M3x12 socket head cap screws, through 3.4 mm holes spaced 30 mm apart vertically. The screws thread into M3 hex nuts captured in 5.7 mm pockets on the back of the web.
Pinned Cleat Rail End Stop
End stop for the 'Printed French Cleat Bin Wall' kit. It is a 20 x 55 x 13 mm block that butts against the end of a 200 mm cleat rail and sits 10 mm above the rail's 45 mm front and 8 mm in front of it, so hangers can't slide off the end. It takes two 4 mm x 20 mm steel dowel pins in 4.3 mm x 11 mm blind holes at d=6, h=10/25, which you can glue with CA. The block is symmetric, so turn it over to use it at the other end of the row.
Printed 45 Degree Cleat Rail
A 200 mm long French-cleat wall rail for the 'Printed French Cleat Bin Wall' kit. It is 12 mm thick and 45 mm tall, with a 45° bevel that the kit's hanger brackets hook onto. It takes three #8 wood screws (4.2 mm shank) through 5.0 x 10 mm slots, with a 10.5 x 15.5 x 4 mm counterbore for the head. Each end has two blind holes 4.3 mm across and 11 mm deep, which take 4 x 20 mm steel pins to join rails end to end. It prints flat on its wall face with no supports.
Dovetail And Peg Fit-Test Coupon
This is the print-first tolerance tester for the 'Dovetail-Stacking Parts Drawer Cabinet' kit. It is a 72 × 14 × 30 mm block that prints standing up. Its three vertical dovetail grooves (7.6/10.6, 8.0/11.0 nominal and 8.4/11.4 mm, all 2.5 mm deep) test a printed Bowtie Dovetail Joiner Key. Three 3 mm deep blind holes (4.1, 4.3 and 4.5 mm) test the Peg-On Drawer Label Holder's 4.0 mm split pegs. Raised 1-, 2- and 3-dot marks show which size is tight, nominal or loose, so you can tell whether your printer will slide the whole cabinet together before you print six housings.
Peg-On Drawer Label Holder
A 60 × 20 × 4.5 mm slide-in label frame for the 'Dovetail-Stacking Parts Drawer Cabinet' kit. A 54 × 16 mm paper or card label slides into a 55 × 16.6 × 1.0 mm pocket from the right-hand end and shows through a 50 × 12 mm window. Two split 4.0 mm × 2.3 mm pegs at ±24 mm press into the 4.3 mm holes in the Detent-Stop Parts Drawer front plate, so you don't need glue or tape.
Notched Drawer Divider
A 55.2 × 36 × 3 mm snap-in divider for the 'Dovetail-Stacking Parts Drawer Cabinet' kit. It drops into the 3.8 mm rib slots at 30, 60 or 90 mm inside the Detent-Stop Parts Drawer. That fits the 70 × 50 × 130 mm Dovetail Drawer Cell Housing drawer and splits it into 2, 3 or 4 compartments. A 24 × 4.5 mm bottom notch straddles the drawer's 23 mm spine, and a 20 × 6 mm finger scallop lets you lift it out. 0.5 mm chamfers on the side edges help it into the slots. It takes no fasteners.
Detent-Stop Parts Drawer
A slide-out drawer for the 'Dovetail-Stacking Parts Drawer Cabinet' kit. It fits the 70 × 50 × 130 mm Dovetail Drawer Cell Housing. The body is 60 × 40 × 121 mm (56 × 38 × 119 mm inside) behind a 68 × 46 × 3 mm front plate, 124 mm deep overall. A 19 mm × 4 mm underside channel rides the housing's 18 mm rail. A 6 mm catch tooth at the back stops against the rail bump, so the drawer can't fall out: lift it about 1 mm to take it out. It has three pairs of 3.8 mm divider slots, two 4.3 mm label-peg holes at ±24 mm and a 45° pull lip, so it prints without supports. No hardware is needed.
Dovetail Cabinet Plinth Foot
The base foot of the 'Dovetail-Stacking Parts Drawer Cabinet' kit. It is a 70 × 130 × 8 mm ladder-frame plinth with a 7.4 → 10.4 mm dovetail tongue on top. The bottom 70 × 50 × 130 mm Dovetail Drawer Cell Housing slides onto the tongue from the front. Four 5.0 mm holes with 9.5 mm 90° countersinks take #8 wood screws (4.2 mm shank) to fix the column down, so it can't tip forward when you pull out a loaded drawer.
Bowtie Dovetail Joiner Key
A 128 mm long double-dovetail (bowtie) key for the 'Dovetail-Stacking Parts Drawer Cabinet' kit. It is 10.4 mm wide at both faces, narrows to a 7.4 mm waist and is 4.4 mm thick. It slides into the 8/11 mm × 2.5 mm dovetail grooves of two neighbouring 70 × 50 × 130 mm Dovetail Drawer Cell Housings and locks them together top-to-bottom or side-to-side, so stacked cells can't pull apart. It needs no screws or other hardware, has 0.3 mm of clearance per side and 0.8 mm lead-in chamfers on both ends, and prints flat with no supports.