Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Shower Tray M5 Jack-Bolt Leveling Foot
This is a single replacement leveling foot for a low-profile shower tray. You don't need to buy a whole new leg kit to fix one cracked corner. It's a 60 mm floor pad with a 26 mm ribbed column 30 mm tall. Inside the column is a captured M5 hex nut (8 mm across flats, slides in from the side). Thread any M5 bolt down through it and turn it to jack the tray up under the cracked foot.
Toilet Tank Rim-Hang Water Saver Bank
A cup that hangs inside a toilet tank and stays full while the tank empties, so each flush uses about 0.35 L less water. Its 2 mm bar sits on the tank rim under the lid, and an 18 mm hook gap fits tank walls up to about 17 mm thick. The 150 x 50 x 70 mm cup has a 45° end wall to clear the flapper. It hangs on an 80 mm drop, so its open top sits 80 mm below the rim and fills on every refill. Measure your fill line before printing: it has to be less than 80 mm below the rim.
Through-Glass Shower Door Knob M5
A replacement shower door knob, 40 mm across and 35 mm tall. Print two and join them through the glass with a length of M5 threaded rod. Each knob has an M5 hex nut pocket (8.3 mm across flats), a 22 mm deep M5 clearance bore and a 25 mm × 2.2 mm recess on the glass face for a rubber washer. It fits 6–10 mm glass with any hole of 6 mm or larger, so you can replace a cracked plastic knob without tracking down the original part.
Double-Prong Bathroom Robe Hook
A two-prong robe and towel hook for the back of a bathroom door or wall. It replaces a snapped zinc hook without having to find the brand's hidden-mount base. It is 91 x 60 x 20 mm, and the 80 mm back plate mounts with two countersunk #8 wood screws (4.2 mm shank) through 4.6 mm clearance holes 40 mm apart. The long upper prong reaches 60 mm from the wall and the short lower one 42 mm. Both have ball tips so fabric won't snag.
Snap-On Toilet Bolt Cap And Washer
A replacement toilet closet-bolt cover: a 34.6 mm dome cap, 37 mm tall, that snaps over a 28.8 mm retainer washer. The washer has an 8.5 mm bore for 1/4" and 5/16" closet bolts and sits under the nut. Both pieces print nested as one job, and the four flex fingers let the washer pop out for fitting.
Spring-Loaded Toilet Paper Spindle
A one-piece replacement spring roller for a wall toilet paper holder: a 22 x 22 mm square spindle (31 mm across the diagonal, so it spins freely inside a 44 mm cardboard core) with a monolithic serpentine flexure instead of a steel coil spring. It is 157 mm long at rest and compresses 10 mm to 147 mm, so it drops into holders with bracket recesses 147-156 mm apart; the 12 mm diamond end nubs self-centre in round or square recesses and print with no overhang past 45 degrees.
Clamp-On Toilet Flush Lever Arm
A 120 mm replacement flush lever arm for a toilet tank, for when the brittle OEM arm snaps at the chain hole and the linkage isn't sold separately. Instead of guessing your handle's tab shape, a 14 mm deep forked jaw slides over the handle blade (1.5–3.6 mm thick) and pinches it with an M3×20 screw and a captured M3 nut; five 4 mm chain holes on a 12 mm pitch set the flapper chain length. Arm cross-section is 5 × 12 mm so the bending load runs along the print's strong axis.