Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Five-Slot Paint Brush Hang-Dry Wall Rack
A 170 x 55 mm wall shelf that holds five washed paint brushes upright with the bristles hanging down so they drip-dry without bending. Its open-front slots are 10, 13, 16, 19 and 22 mm wide to fit thin artist brushes up to thick 3 in trim brushes. It mounts with two #8 wood screws through 5 mm holes 68 mm apart, and gussets between the slots carry the load.
Three-Hook Padlock Wall Ladder
A 176 mm tall wall-screwed spine with three lipped J-hooks spaced 58 mm apart, so padlocks, bike locks and key rings each hang on their own hook. The 8 x 6 mm arms fit any shackle with at least a 9 mm inner gap and give 27 mm of reach. It prints on its side so the hooks carry load along the layers, not across them, and it mounts with two #8 / M4 screws through 4.5 mm counterbored holes.
Graduated Eight-Slot Wrench Wall Rack
A 178 mm screw-on wall rack for combination wrenches. It has eight open-front slots that step from 10 mm to 20.5 mm wide, so the shank drops in and the box end rests on top. A 2 mm front lip keeps each wrench from sliding off. The ledge sits on a 45° wedge, so it prints standing upright with no supports, and it hangs from three 4.6 mm holes that take #8 wood screws or M4 screws.
Six-Slot Fishing Rod Wall Rack
This is a 168 x 56 mm rack that screws to a garage wall and holds six fishing rods upright, with the butts resting on the floor. Each slot has a 17 mm keyhole pocket behind a 12 mm throat with a flared mouth, so a rod blank or ferrule up to about 16 mm sits in the pocket and lies back against the wall. It mounts with three #8/#10 wood screws or M5 screws through 5.5 mm holes, and the 6 mm arm is braced by four 45° gussets.
Three-Cup Oil Funnel Drip Wall Rack
A wall rack that holds garage funnels spout-down in three closed tapered cups. The cups open at 26, 34 and 42 mm and are 58 mm deep, so the funnel's cone sits on the rim and leftover oil, coolant or fuel drips into the sealed cup and stays off the floor. The 148 x 80 mm backplate takes two 5.5 mm holes for M5, #8 or #10 screws, and the cups are 2.4 mm thick with ribs tying them to the wall. Any funnel whose spout fits a cup will seat in it.
PVC And EMT Offcut Socket Wall Rack
This wall rack has five upright sockets that keep short pipe offcuts sorted by size: 1 in (33.4 mm OD), 3/4 in (26.7 mm) and 1/2 in (21.3 mm) schedule 40 PVC, plus 3/4 in (23.4 mm) and 1/2 in (17.9 mm) EMT conduit. Each 36 mm deep socket is 1.5 mm over the pipe's OD and has a drain hole in the floor. The 156 x 52 mm back plate takes two #8 wood screws.
Pressure Washer Five-Tip Wall Rack
A wall-mounted rack for the five 1/4 in quick-connect tips that come with most electric pressure washers (0°, 15°, 25°, 40° and soap). Each tip drops plug-first into a tapered cone socket, 15 mm across at the top and 7 mm at the bottom, so tips of different sizes all seat snugly and water drains out through the bottom. The rack is 130 x 26 x 55 mm and screws to a stud or the washer cart with two #8 wood screws through 5 mm holes. Side cheeks brace the ledge against the backplate.
Three-Size Hammer And Mallet Wall Rack
A 164 x 95 mm wall shelf with three closed drop-through slots (28x40, 32x46 and 38x52 mm). Each hammer or mallet hangs handle-down with its head resting on the shelf, and the slots sit 60 mm out from the wall so a 110–120 mm claw head clears it. It screws to a stud or anchors through three 4.5 mm holes sized for #8 (4.2 mm) or M4 screws. It prints with the shelf flat and the gussets pointing up, then mounts flipped so the gussets brace underneath.
Bungee Cord Seven-Peg Wall Rail
A 160 x 42 x 44 mm wall rail with seven pegs on 22 mm centres. Each peg has a 9 mm flat seat and an 8 mm lip, so a bungee cord's steel hook drops on and stays put instead of ending up in a tangle in a bucket. It mounts with three #8 pan-head or washer-head wood screws through 4.8 mm holes. Each peg is printed as a 6 mm upright fin, so the hanging load runs along the layers and can't peel them apart.
Flagged: lifting or tensioned load. Not for safety-critical use without independent engineering review.
Test Lead And Clip Wall Rack
A 150 mm wide wall rack with ten 5.2 mm drop-in slots. Each slot takes a meter lead or patch lead with wire up to about 5 mm OD, and the banana plug or probe body rests on top so the leads hang straight and don't tangle. A 3 mm clip rail along the top holds alligator and hook clips. Two gussets and the center rib brace the 40 mm deep shelf. Mount it with two #8 wood screws or M4 bolts through the 4.6 mm holes, which are 90 mm apart.
French Cleat Bar Clamp Rack Arm
A cantilever storage arm that drops onto a standard 45-degree French cleat ripped from 3/4 in (19 mm) plywood, sized to hang F-clamps and bar clamps by their bars — the arm reaches 92 mm past the cleat face, rises 7 mm toward the tip and ends in a 16 mm upturned lip so clamps slide back instead of walking off. It is 112 x 72 x 15 mm and prints on its side, so the bending load at the arm root runs along the layer plane, and a 4.5 mm cross bore through the 9 mm back plate takes a #8 wood screw or M4 bolt into the cleat board to lock it against lift-off.