Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Sump Pump Float Cord Zip-Tie Pipe Clamp
Replaces the small plastic clip that snaps off and lets a tethered float switch cord slide down the sump discharge pipe. A 90° V-saddle seats any pipe from 1-1/4 to 2 in (42–60 mm OD), and two zip-tie tunnels lock it to the pipe. A 10 mm top groove with two more tunnels grips float cords up to about 9 mm, so you can set the tether length by sliding the cord before you cinch it. The clip is 40 x 60 x 40 mm and takes standard ties up to 4.8 mm wide.
Split Loom 45° Branch Y Trough
A screw-down Y fitting for split-loom harnesses. A 26 mm main channel takes the trunk run, and a 20 mm branch at 45° takes the wires that split off, so you don't have to tape two looms together at the junction. Under-floor zip-tie grooves let a tie wrap each loom end even after the part is screwed flat, and three 4.5 mm holes take #8 screws. It's 112 mm long and 22 mm tall.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
Snowblower Shear Bolt Spare Keeper
A 96 x 28 mm keeper that zip-ties into a 90° V-saddle on a snowblower or mower handle tube (fits roughly 16–35 mm OD) and holds four spare shear bolts with their nuts. Each wing has one 6.8 mm hole for 1/4 in or M6 bolts and one 8.6 mm hole for 5/16 in or M8 bolts, so the spares stay on the machine instead of getting lost in a drawer.
Square Tube Corner Zip-Tie V-Saddle Mount
This 50 x 44 x 34 mm saddle has a 90° V-notch that seats on the outside corner of any square tube or angle-iron leg from about 20 to 50 mm, including gate frames, shelving uprights and trailer rails. It also works on round pipe. Two tunnels sized for ties up to 5.5 mm wide pull it tight against the corner. The flat back face has two M4 heat-set insert bores 20 mm apart, so you can bolt on a light, sign, hook or sensor without drilling the tube.
ATO Fuse Tap Zip-Tie Dash Mount
A small cradle that stops an add-a-circuit fuse tap dangling behind the fuse box. A U-channel with a 16 mm inner width holds the tap body and two bridged tunnels in the floor take zip ties up to 5 mm wide. A 3.6 mm comb slot gives the pigtail wire strain relief, and one 4.5 mm hole takes an M4 screw or a #8 (4.2 mm) sheet-metal screw. It is 62 x 24 x 15 mm overall.
Zip-Tie Collet Bicycle Kickstand Foot
A replacement foot for a bicycle kickstand whose rubber tip has worn through or snapped off. A 22.5 mm four-slit collet socket fits round or flattened leg ends about 19–22 mm across and clamps shut with one 4.8 mm zip tie in the outer groove. The 80 x 56 mm buttressed pad keeps the bike from sinking into gravel or grass, and a drain hole stops water collecting in the socket.
Zip-Tie Bar Clamp Jaw Pad
A snap-free pad for bare steel F-clamp and bar-clamp jaws. It is 60 x 40 x 19 mm, with a 32 mm channel that takes any jaw 20–30 mm wide, and two zip-ties run through floor grooves and rail slots to cinch it on. The flat face has a 6 mm 90° V-groove, so the clamp can hold dowels and pipe as well as flat stock without marring them.
Snap-Slot Wire Harness Lacing Comb
A 110 x 50 x 10 mm lacing comb for building neat wiring looms. Wires press sideways through V lead-ins and snap into seats, so you never have to thread them from the end: 12 seats on the top edge are 3.2 mm with a 2.2 mm neck at 8 mm pitch (about 18–22 AWG hookup wire), and 8 seats on the bottom edge are 4.6 mm with a 3.2 mm neck at 11 mm pitch (about 14–16 AWG). There is a 60 x 12 mm finger window in the middle, and two M4 clearance holes let you screw it to a harness board or slide it along the bundle while you zip-tie or lace the wires at even spacing.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
Cable Tie Length Sorting Caddy
A five-bay stair-stepped caddy that keeps zip ties sorted by length (roughly 100 / 150 / 200 / 250 / 300 mm) instead of tangled in one bag — bay widths run 14 to 20 mm, each with a front window so you can pinch one tie out single-handed. Footprint is 100 x 26 mm with bay walls 30 to 46 mm tall; it stands on the bench or screws to a wall through two 4.5 mm M4 clearance holes in the 4.5 mm back wall, driven from inside bays 2 and 4.
Garage Door Safety Eye Bracket
A replacement mounting bracket for garage door opener safety photo eyes, for when the original snapped or never fit your track. The 38 x 100 x 5 mm plate screws to the vertical door track with #8 self-tappers through four 4.5 mm holes plus two 4.5 x 22 mm height-adjustment slots; the 46 mm sensor wall takes any eye with two zip ties through the 7 x 3.5 mm slots or an M4 heat-set insert, and the angled hood shades the lens from low sun that causes phantom reversals.
Relay And Fuse Zip-Tie Mount Base
A 106 x 52 x 6 mm mounting base (142 mm overall with the screw feet) that gives automotive relay sockets and inline fuse holders something to bolt to instead of dangling off the loom. Two 33 mm bays between 3 mm divider ribs take 4- and 5-pin relay sockets, a 45 degree V-saddle bay cradles round inline fuse holders from roughly 8 to 16 mm, each bay has a pair of 8 x 3.2 mm slots plus a recessed underside channel so a 4.8 mm zip tie loops over the part without lifting the base off the panel, and the two ears carry 4.5 mm M4 clearance holes for firewall or bulkhead screws.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.