Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Slot-Adjust Print-In-Place Surface Cabinet Hinge
This surface-mount butterfly hinge prints in place. Each 64 x 28 x 3 mm leaf has a 9 mm five-knuckle barrel with a 5 mm pin running in a 6 mm bore, so the pin has 0.5 mm of clearance all round. It replaces discontinued non-Euro hinges on older face-frame cabinets. The 3.8 mm slots for #6 wood screws (3.5 mm shank) run lengthwise on one leaf and crosswise on the other, so you can line them up with the old screw holes instead of drilling new ones.
Sliding Screen Door Slotted Pull Plate
Replacement pull for sliding patio screen doors whose Prime-Line / Slide-Co style mortise handle is discontinued: a 40 x 150 x 3 mm cover plate hides the old mortise pocket (up to 28 x 70 mm) and carries a 70 mm long, 26 mm tall 45-degree hooked grip. Two 4.5 x 24 mm vertical slots take the original 8-32 or M4 through-bolts at any hole spacing from 80 to 128 mm (3-1/8 to 5 in); print two and bolt them back-to-back through the door stile for an inside and outside pull.
Pilaster Shelf Clip Four-Width Sprue
Snap-off sprue of 16 hook-style shelf clips for slotted steel pilaster standards in bookcases, closets and store shelving, four clips each in 3.4, 4.0, 4.6 and 5.2 mm prong widths so you can match a slot the shops no longer stock (pick the column 0.2 to 0.3 mm under your measured slot width). Each clip is a single top hook (1.8 mm thick, 1.5 mm crook for steel up to 1.4 mm, needs a slot at least 6 mm long and 3.5 mm of cavity behind the strip) over a 16 mm bearing pad, with a 14 mm gusseted ledge and 2 mm front lip; it works on any slot pitch, and in PETG expect roughly 5 kg per clip, about a quarter of the steel originals.
Window Screen Push-In Pull Tab Set
A set of four replacement window screen pull tabs that push into the spline channel beside the rubber spline, replacing the vinyl tabs that crumble in the sun. Each tab is a 10 mm wide finger loop (15 mm outer diameter, 9.5 mm hole) on a 12 x 2.4 mm base that sits on the frame lips, with a 1.2 mm thick barbed leg in four lengths (5, 7, 9 and 11 mm) to suit shallow and deep channels around a 3.6 mm spline; the whole set prints flat on its side so layer lines run along the loop-to-leg bend and the tabs snap apart on 1 mm thick sprues.
Screw-On Pocket Door Edge D-Pull
This is a D-loop pull that screws onto the leading edge of a pocket door, so you can grab a door that has slid all the way into the wall. It is 90 x 28 x 26 mm and has two countersunk 4.6 mm holes for #8 (4.2 mm) wood screws or M4 screws. The 26 mm wide base fits 1-3/8 in (35 mm) and 1-1/8 in (28.6 mm) interior door edges, and the 52 x 17 mm finger opening fits fingers of any size. It prints on its side so your pull goes across the layers, not against them.
Set-Screw Ceiling Fan Chain Pull
This fluted bell-shaped pull is 22 mm across and 42 mm tall. It replaces the pull on a ceiling fan or lamp chain after the old one snaps off. Bead chain up to about 4 mm feeds through a 4.5 mm centre channel, and one side-entry M3 screw threads into a 2.6 mm self-tap hole to clamp it. A 7 mm × 12 mm pocket in the base hides the chain tail or an old connector.
96 mm Cabinet Bar Pull With M4 Inserts
A 124 mm bar pull for kitchen cabinets and drawers that fits the standard 96 mm hole spacing. It takes M4 brass heat-set inserts (5.5 mm bores, 10 mm deep), so you can replace one broken or discontinued handle without buying a whole matching set. It prints lying on its side, so the pulling load runs along the layers instead of across them, and it leaves a 22 mm deep finger gap behind a 10 x 14 mm grip bar.
Casement Window Crank Handle
Replacement folding-style crank handle for casement and awning window operators whose original plastic handle has stripped or gone missing — the mechanism outlives the handle and the OEM part is usually only sold as a whole $40–80 operator. The 26 mm OD hub has a 9.6 mm through bore and two opposed M4 heat-set inserts (5.5 mm bores) so set screws grip any splined, D or round operator stub from 5 to 9.5 mm; 80 mm crank throw, 16 mm dia grip, 105 mm long overall, 44 mm tall. Print in PETG or ASA if the window gets direct sun.