Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Screw-On Drywall Outside Corner Guard
A 150 mm tall L-shaped guard that screws over a 90° outside drywall corner. It stops vacuums, strollers and furniture from crushing the corner bead. Each flange is 32 mm wide and 3 mm thick, with a 6 mm bullnose at the corner and a 2 mm relief groove so it sits flat over a raised metal bead. It has five staggered 4.5 mm countersunk holes for #6 (3.5 mm) or #8 (4.2 mm) wood screws, or for screws in plastic drywall anchors.
Mid-Span Sagging Shelf Truss Bracket
This truss bracket screws to a stud under the middle of a sagging closet or pantry shelf and lifts the sagging span. The wall leg is 126 mm tall and the arm is 150 mm deep. Two 4.6 mm holes in the wall leg take #8 (4.2 mm) wood screws, and two 4.0 mm holes in the arm take #6 (3.5 mm) screws up into the shelf. A 9 mm bore through the diagonal brace gives a driver a straight path to the upper wall screw. The part prints flat on its side, so the shelf load runs along the layers instead of across them.
Ribbed Fence Picket Break Splint
A 70 x 150 mm ribbed splint plate that screws across a cracked or snapped wood fence picket. Use it to fix the one broken board without buying and cutting a new one. It is 4 mm thick with two 10 mm tapered stiffening ribs, and it has eight countersunk 4.8 mm holes for #8 (4.2 mm) wood screws, four on each side of a centre alignment groove. The plate sits flat on any picket from about 75 mm (3.5 in) wide upward, so the board's thickness doesn't matter.
Swivel Cabin Hook On #10 Screw Pivot
A 122 mm swivel cabin hook that pivots on a #10 wood screw (4.8 mm shank) or an M5 bolt through a 5.5 mm bore. Its 8 x 7 mm throat catches a standard screw eye to keep shed doors, gates and cupboard doors from swinging open. The 10 x 6 mm bar is printed flat so the pull runs along the layers instead of across them. A 2 mm raised boss keeps the bar clear of the door face and trim.
Slotted #8 Screw Chair Corner Block
Printed corner block that fixes a wobbly chair seat frame or table apron. It screws across the inside corner of two aprons, and a 45° notch clears the leg. The 80 x 80 x 28 mm open truss has 7 mm flanges, two slotted, counterbored #8 (4.2 mm shank) screw holes per side so you can set the block flush with the apron's top edge, and 10 mm driver access ports through the diagonal web.
Squeeze-Fit Two-Hole Pipe Strap
This two-hole wall strap is sized to one exact pipe. The default is 3/4 in EMT (23.4 mm OD). You can change PIPE_OD to 17.9 for 1/2 in EMT, 21.3 for 1/2 in PVC, 26.7 for 3/4 in PVC or 33.4 for 1 in PVC, so the strap always matches the pipe even when the store doesn't stock that size. The flanges stand 1 mm off the wall, so two #8 wood screws in 4.5 mm holes draw the 3.5 mm arch down and clamp the pipe tight. The part is 16 mm wide and prints flat on its side, which keeps the clamping load in the layer plane.
Screw-On Curtain Tieback Holdback Hook
A curtain holdback that screws to the wall or window trim. Two #8 wood screws (4.2 mm shank) go through 4.6 mm clearance holes, 48 mm apart, with 8.5 mm counterbores for pan heads. A 51 mm deep cradle with an 18 mm lip holds a gathered drape open. The hook stands 64 mm tall, reaches 65 mm from the wall and is 16 mm wide. It prints on its side, so the curtain's weight runs along the layers instead of peeling them apart, and a gusset under the arm stops it drooping.
Stripped Screw Hole Repair Plug Set
A snap-off set of six barbed, split-top plugs that fix stripped wood-screw holes in particleboard cabinet doors, hinges and furniture. You get two of each size: #6 (drill 6 mm, 2.5 mm pilot), #8 (drill 7 mm, 3.2 mm pilot) and #10 (drill 8 mm, 3.8 mm pilot). Each plug is 24 mm long. Drill out the stripped hole, glue the plug in, trim it flush and drive the screw. The screw spreads the slotted top so it grips the wood.