Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Rain Chain Tapered Gutter Outlet Adapter
A drop-in tapered spout that replaces a downspout with a rain chain. The 40 mm cone tapers from 74 to 46 mm OD, so it self-centres in any round gutter outlet hole from about 48 to 72 mm. The 100 mm flange sits on the gutter floor with three 4.5 mm holes for #8 screws or 1/8 in rivets and a bead of gutter sealant. A 12 mm crossbar spans the bore: the chain's top link hooks over it, or an M5 eye bolt goes through the 5.5 mm centre hole.
Downspout Elbow Snap-In Wind Clip
This wall clip replaces the factory clip that wind snaps off a folding downspout elbow. Two flexing arms and ramped hooks snap around rectangular "2x3 in" downspout up to 80 mm wide, and a built-in bow spring presses spouts 50–60 mm deep forward against the hooks so they don't rattle. The clip is 130 x 82 x 25 mm and fixes to the wall with two #8 screws through 4.5 mm holes in the side wings. It prints flat without supports, and the arms flex within the layers, so wind load never pulls across the layer lines.
Downspout Extension Stake-Down Saddle
This saddle straps a downspout extension to the ground so it can't blow away or get kicked off. It has a 90 x 62 mm opening, which takes a 2x3 in rectangular extension or a 3 in round corrugated one. Each 28 mm foot has a 6.5 mm vertical bore for a tent peg, 6 mm steel rod or #10 screw. The part is 156 mm wide, 20 mm deep and about 38 cm³. It prints on its side, so ground-pull loads run through the layers, not across them.
Tapered Downspout Leaf Strainer Dome
A replacement leaf strainer for a gutter outlet. Its 23° tapered plug, 52 mm across at the tip and 82 mm at the shoulder, wedges into any round drop outlet with a 52–82 mm bore, so the same part fits 2 in, 2.5 in and 3 in outlets where one-size wire baskets rattle loose. The 96 mm cage has 16 ribs and 4.5 mm slots that let water through and hold back leaves. An 8 mm loop on top lets you hook it out with a stick for cleaning.
Twin-Band Downspout Wall Standoff
This is a wall-mounted standoff block for a gutter downspout. It measures 130 x 60 x 11 mm and screws on with two #10 or M5 screws (5.5 mm countersunk holes). Two 14 x 3.5 mm tunnels run through it for zip ties or 1/2 in (12.7 mm) worm-drive hose-clamp bands. The band wraps around the downspout, so one part fits 2x3 in (about 51 x 76 mm nominal), 3x4 in or any other profile, and it replaces the brittle vinyl straps that snap every winter.
2x3 Downspout Rain Barrel Diverter
A screw-on side-outlet diverter for standard 2x3 in (51 x 76 mm) rectangular aluminium downspout: cut a 58 x 34 mm window in the spout face, seal and screw this 74 x 84 mm flange over it with four #8 or M4 screws, and the 30 degree chute throws the flow sideways into a rain barrel lid instead of the flowerbed. The chute is a 64 x 40 mm rectangular tube with 3 mm walls, 58.5 mm tall as printed, gusseted at the flange so a full column of water can't snap it off — print in ASA or PETG for UV life.