Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Tethered Drip Line Goof Plug Sprue
A 120 mm snap-off sprue with six barbed, tapered drip-line goof plugs. Three are small (4.0 mm tip, 6.0 mm barb) for 3.5–5.5 mm punched holes and 1/4 in tube ends, and three are large (5.2 mm tip, 8.2 mm barb) for torn or 5–7.5 mm holes. Each plug has a flexible tether ending in a 5.4 x 2.4 mm slot that takes a standard 3.6–4.8 mm zip tie, so you strap it to the mainline and don't lose it. The taper lets each plug fit a range of holes, and the 45° barb holds it in place.
3/4 in PVC Sprinkler Zone Snap Tag
A snap-on zone tag for 3/4 in schedule 40 PVC (26.7 mm OD) irrigation manifolds and valve-box risers. It has a 27 mm C-clip bore and a 22.7 mm mouth, so it clicks onto the pipe without tools. The 66 x 32 mm paddle has a recessed panel for paint pen or a label, plus eight snap-off tabs along the top edge. Break off tabs to count out the zone number so it can still be read after the ink fades in the valve box, and use the 4 mm hole to wire on a backup tag.
Open-Bottom Low-Voltage Splice Hood
A one-piece rain hood for wire-nutted 18–22 AWG low-voltage splices, such as sprinkler valve wire, landscape lighting or doorbell cable. It mounts open end down so water drains out instead of collecting. The cavity is 60 x 38 x 70 mm, with two ribs inside that have zip-tie slots for strain-relieving the bundle and a rear notch for a cable running along the wall. Overall it's 90 x 44 x 72 mm and fixes with four #8 wood screws through 5 mm ear holes.
1/2 in PVC Sprinkler Riser Tripod Hub
A tripod hub that turns four lengths of 1/2 in Schedule 40 PVC (21.3 mm OD) into a free-standing tall sprinkler stand that throws water over tall vegetable beds. The three 38 mm deep leg sockets splay out at 25°, a 21.7 mm slip bore runs through the centre for the riser, and an M4 thumb screw locks the riser at any height. Footprint is about 112 mm across and it stands 50 mm tall.
Drip Tubing V-Groove Square-Cut Block
This is a bench block for squaring the ends of drip-irrigation poly tubing before you push it onto barbed tees and elbows. It has a 90° V-groove 22 mm wide for 1/2 in poly tubing and a 10 mm groove for 1/4 in tubing, and both are crossed by a 1.2 mm utility-blade slot. A crooked cut is the usual reason a new fitting leaks or splits. The V-grooves hold any tube diameter, so they work across the 15–18 mm OD spread of 1/2 in drip line from different brands. The block is 80 x 44 x 22 mm.
Sprinkler Head Mower Guard Collar
A 130 mm sloped ring that sits flush in the turf around a pop-up spray or rotor sprinkler head. Its 70 mm bore clears caps up to about 65 mm across, and the 19° ramp lets mower wheels and trimmer line ride over the head instead of snapping it. Four 5.5 mm holes take tent pegs, 6 in nails or landscape staples to hold it down, and the part is 11 mm tall at the bore with a 1.6 mm outer edge.
1 in PVC Snap-In Fence Standoff Clip
Snap-in saddle clip for 1 in schedule 40 PVC (33.4 mm OD). The pipe pushes through a 28 mm mouth into a 33.6 mm cradle, and the clip holds it 12 mm off a fence, post or wall so wood can dry behind the run. It suits irrigation, solar conduit and garden hoop runs. The 70 x 20 mm foot takes two #10 wood screws (5.3 mm clearance holes on 56 mm centres), and the ring prints flat so any pull on the pipe goes along the layers.