Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Slotted-Span Fridge Door Pull Handle
A 170 mm replacement pull handle for a refrigerator or freezer with a cracked or snapped handle. The two feet have 10 mm slots for M4 or #8 screws, so it fits screw spacings anywhere from 136 to 156 mm without drilling new holes. The bar stands 26 mm off the door to leave room for your fingers, and the screw heads sit in 9 mm counterbore channels you reach from the front. It prints flat, so the pulling force runs along the layers instead of across them.
Tapered-Socket Radiator Bleed Key
A winged radiator bleed key. The socket is a square that tapers from 6.6 mm at the mouth to 4.4 mm at the bottom, 11 mm deep, so it wedges onto any square bleed-valve spindle in that range instead of relying on one guessed size. The part is 64 x 16 x 24 mm: a gusseted 18 mm barrel on a flat wing that takes the turning load along its layers, plus a 5 mm keyring hole so the key stays with the boiler.
Table Leaf Alignment Pin And Socket Set
Two press-in alignment pins and two flanged sockets that keep extension-table, drop-leaf and two-piece desk leaves level. Drill both edges to 12 mm. The pin shanks and socket sleeves have crush ribs (12.5 mm across the ribs) that grip the wood. Each 8.2 mm nose slides into an 8.8 mm socket bore that has a chamfered lead-in. The parts print on a breakaway sprue, and the set replaces the plastic leaf pins that hardware stores no longer stock.
Slotted Hook Window Sash Lift
A replacement hook-style lift for the bottom rail of a double-hung window. It is 60 mm wide, 45 mm tall and projects 26 mm, with a 16 x 10 mm finger pocket under the hook. Two 4.5 mm slots fit #6 (3.5 mm) or M4 pan-head screws at any spacing from 30 to 44 mm, so it lines up with the old screw holes after the original cast lift breaks.
Bathroom Pull-Cord Switch Acorn Grip
A replacement acorn grip for a bathroom ceiling pull-cord switch. It's 28 mm across and 46 mm tall, with a 3.5 mm cord bore and an 18 mm knot pocket that opens at the bottom. A 2.2 mm side slot lets you press a 2–3 mm cord in from the side, so you never have to unthread it or touch the switch. A 45° roof over the pocket lets it print without supports, and eight flutes give you something to grip with wet hands.
Notched RV Roof Vent Prop Stay
A replacement prop arm for manual caravan/RV roof vents and hatch lids. It's a 168 mm long, 18 mm wide, 7 mm thick bar with a bossed 5.5 mm M5 pivot hole at one end. At the other end is a 90 mm slot with six notches 16 mm apart, so the stud on the lid can rest at six different opening heights. The slot lets it fit lids whose stud sits anywhere along that range, so you don't need the discontinued dealer part.
Tension Pole Caddy Replacement Shelf
A 120 x 90 mm draining shower shelf that replaces a cracked or lost tray on a corner tension-pole shower caddy. Instead of a moulded collar sized to one pole, it has a 90° V-saddle that seats any pole from 22 to 30 mm. Two worm-drive hose clamps (bands up to 12.7 mm wide) run through 14 x 3.2 mm tunnels in the 62 mm tall clamp block and hold it in place. The floor has drain slots, two gussets carry the shelf load into the clamp block, and the front lip is lowered so bottles lift out easily.
Pinch-Clamp RV Dump Valve T-Handle
A replacement T-handle for RV black and grey tank dump valves with an 8 mm stem. It clamps onto the stem with one M4 pinch bolt and a captured M4 nut, so you don't need a pin or set screw. The 110 x 58 x 16 mm grip lies flat on the printer bed so the pulling force runs along the layers, and it has finger scallops and lanyard slots. The 8.3 mm bore is 17 mm deep, with a 4 mm solid entry collar ahead of the split jaw.
Pet Door Flap Clamp Rail With 5 mm Pin Barrel
A replacement top rail for flap-style pet doors whose original hinge rail has snapped and is no longer sold. It is 160 mm long and 30 mm tall. A 3.5 mm slot takes a vinyl or rubber flap up to about 3.2 mm thick. Five M3 bolts at 32 mm spacing go through the flap and seat in captured hex nuts, and a 5.3 mm bore along the top runs on a 5 mm steel rod used as the hinge pin. Check that your frame takes a 5 mm pin before ordering.
Pull-Down Faucet Hose Split Weight
A two-piece weight that bolts onto the hose of a pull-down kitchen faucet, under the sink, so the sprayer pulls back into its dock again. It replaces the weight that slides off or gets lost and isn't sold on its own. Print two identical 80 x 40 x 16 mm halves. They fit braided hose of about 9–11 mm OD with grip ribs and close with four M4 x 25 cap screws and nuts. Two sealed 8 x 44 mm pockets inside hold steel BBs or scrap nuts set in hot glue to add weight.
Set-Screw Patio Umbrella Rib Tip Cap
This is a replacement end tip for a patio umbrella rib. The rib slides into a 9 x 6.4 mm socket that is 26 mm deep, which takes steel U-channel ribs up to about 8.5 x 6 mm or round fibreglass ribs up to 6 mm. Two M3 set screws, self-tapped into raised bosses, clamp the tip to the rib. A 6 mm neck and an 11 mm knob hold the canopy's corner pocket, so the fabric stops tearing on a bare rib end. The tip prints lying flat, about 55 mm long, so canopy tension runs along the layer lines.
Standoff Pivot Shutter Dog
This S-shaped shutter dog replaces the rusted or snapped one that holds exterior shutters open. A #10 (4.8 mm) wood or masonry screw goes through a 5.5 mm bore in a 36 mm standoff boss, and an 11 mm recess keeps the screw head flush. The heavier lower tail makes it hang upright on its own, so the upper hook laps over shutters 22–29 mm thick; sand the boss down for thinner shutters.
Shower Caddy Suction Cup Rail Hanger
This is a replacement suction-cup corner for a hanging shower caddy (44 x 80 x 18 mm). Its keyhole has an 11 mm entry and a 5.5 mm slot, which takes a standard mushroom-head suction cup or an M5 threaded-stud cup. A 6.5 mm channel holds a 4–6 mm wire or rod top rail, and two M3 cross-screws keep the rail in, so you can fix a caddy whose corner snapped off instead of throwing it away.
Square Towel Bar End Post Replacement
A replacement square-style towel bar end post that screws straight to the wall with two #8 screws, so you can keep your bar when the original post snaps off. The 19.6 mm blind socket takes 3/4 in (19.05 mm) round bars, and an M4 set screw in a heat-set insert also clamps 5/8 in (15.9 mm) bars. It holds the bar centre 50 mm off the wall. Print one, then flip it over to use it on the other end.
Turntable Dust Cover Stop Hinge
A 60 mm wide print-in-place hinge for a turntable dust cover. It replaces lost or broken lid hinges, and a built-in post stops the lid at about 100° so it can't fall back. Mounts with M3 screws: 3.4 mm holes in the lid leaf, and 10 mm long slots in the plinth leaf so you can set the height.
Cornhole Folding Leg Pivot Bracket
This bracket replaces the stamped-steel folding-leg hinge on a cornhole board, which tends to bend or rust. It screws to the inside of a 2x4 frame rail (89 mm tall) with four countersunk #8 wood screws through 4.6 mm holes. It has an 8.3 mm pivot bore for an M8 or 5/16 in carriage bolt, a raised 3 mm washer boss for the leg to turn on, and a gusseted stop wall. The stop face sits 45.5 mm from the pivot so a 3.5 in (89 mm) 2x4 leg stops square to the rail. The plate is 102 x 85 x 6 mm; print it in PETG or ASA for outdoor use.
150 mm Microwave Turntable Roller Ring
Replacement microwave turntable support ring for ovens whose glass tray rides on a 150 mm roller track. It has three 18 mm rollers on radial pins, a 168 mm OD ring and a loose 36 mm hub that drops over drive couplers up to about 34 mm. The ring, rollers and pins are all PLA with no metal inside. They print together on breakaway sprues: snap them off, drop each roller between its cheeks and push the headed 4 mm pin through, where the inner cheek grips it. The tray sits 18 mm above the floor and the ring clears it by 2.5 mm.
Pedestal Sink Single-Lug Wall Hanger
A replacement for the discontinued steel hanger that holds a pedestal sink's back edge to the wall. You print two and screw each one wherever the sink's rear slots land, so any lug spacing works. Each one is 36 mm wide, 80 mm tall and stands 30 mm off the wall, with an 8 x 14 mm upright tab that the sink's slot drops onto. Two vertical 5.3 mm slots take #10 (4.8 mm) wood screws into blocking and give 10 mm of height adjustment. The hook is printed on its side, so the sink's weight never pulls across the layer lines.
3 in Mower Deck Anti-Scalp Roller
This replaces the plastic anti-scalp roller on a mower deck: a crowned roller 76 mm (3 in) across and 38 mm wide with a 10.0 mm plain bore that turns on a standard 3/8 in (9.5 mm) shoulder bolt. The hub stands 2 mm proud of the rim on one side so the rim never rubs the deck bracket. Six ribs and drain holes keep it light at about 60 cm³, so grass clippings and water don't pack inside. Before you order, measure your old roller's diameter, width and bolt size.
Medicine Cabinet Snap Jaw Door Catch
A snap-jaw door catch for medicine cabinets and small cupboard doors. A 33 x 19 mm catch screws to the cabinet wall through two 4.5 mm slots (for #6 wood screws or M4, with 8 mm of adjustment), and a 30 mm wide strike with a 6 mm knob screws to the back of the door. Two flexing jaws with ramped detents hold the knob shut, so it replaces worn-out magnetic or roller catches. Both pieces print together with the knob already sitting in the jaw (0.5 mm clearance), so you pull the strike out once after printing.
Attic Ladder Drop-In Cord Pull Handle
A replacement pull handle for the pull cord on a spring-loaded attic ladder hatch, which is usually the first part to snap off. The rope drops into a 3 mm slot over a 5.5 mm channel and a knot locks in a 13 x 12 mm pocket, so you don't have to re-thread the cord through the panel. The 86 x 70 mm grip is 10 mm thick with a 68 x 24 mm opening that fits four fingers or a hook pole. It prints flat, so the pulling load runs along the layers.
Brew-Through Universal Carafe Lid
A replacement lid for drip coffee carafes and pitchers whose original lid cracked or was lost. The tapered 2 mm skirt wedges into any round mouth from 58 to 76 mm inside diameter, and an 86 mm cap sits on top. The cap has a 14 mm brew-through centre hole, a 12 x 14 mm pour slot and a flat pull tab. The part is 97 x 86 x 30 mm. Before ordering, measure your carafe's inside mouth diameter; print it in PETG if it will hold hot coffee.
Flex-Fin Tension Shower Rod End Cap
A replacement wall foot for spring-tension shower and curtain rods whose rubber caps have cracked. Six angled flex fins inside a 29 mm cup grip any 22–26 mm tube (7/8 in to 1 in) and stop it spinning. The foot is a 56 mm flat disc with a 45° flare into the cup; stick a 50 mm rubber furniture pad on the face so it grips tile.
Greenhouse Vent Opener Slotted Arm
A replacement for the plastic link arm that snaps on wax-cylinder greenhouse and cold-frame vent openers. It is a ribbed 169 mm strap. One end has a 5.5 mm M5 eye with a captive hex-nut pocket. The other end has a 35 mm adjustment slot, so it bolts to the existing lid bracket at any length and no exact OEM hole spacing is needed.