Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Washer-To-Dryer Stacking Foot Cup
A cheaper replacement for the OEM stacking kit: four of these cups go on top of a front-load washer, and each dryer leveling foot drops into a tapered cup (36 mm at the floor, 44 mm at the 12 mm rim), which fits any foot from about 25 to 42 mm across. Each 100 x 60 x 3 mm plate fixes down with two #8 sheet-metal screws through 4.6 mm slots and has a 27 x 4 mm slot for a 25 mm anti-tip strap. The cup walls stop the dryer from walking off the washer.
Tool Case Print-Aligned Hinge With 4 mm Pin
A 60 mm five-knuckle replacement hinge for stackable tool cases and toolbox lids whose moulded plastic hinge has snapped. The two 21 x 3 mm leaves print flat in one go with their knuckles already lined up. Afterwards you tap in a 60 mm length of 4 mm steel rod: the leaf with three knuckles grips the rod, and the other leaf swings on it. Each leaf has three M4 / #8 slots on a 20 mm pitch, with ±3 mm of play so they can line up with the old holes.
Garage Door Slotted D-Pull Lift Handle
A heavy D-pull lift handle that replaces a cracked plastic garage door handle or step plate. It's 150 mm long and 50 mm deep, with a 64 x 34 mm opening wide enough for gloved fingers. It mounts with two #10 (4.8 mm) pan-head screws through 5.3 mm slots, so the hole spacing can be anywhere from 100 to 124 mm. The slots let you shift each screw to land on a door stile or rib. It prints on its side, so the pull load runs along the layers, and gussets reinforce each corner.
1 in Wire Shelf Post Split Sleeve Pair
Replacement wedge-collar sleeve pair for 1 in (25.4 mm) wire-shelving posts (Metro, HDX, Whalen/Costco, Seville style), printed upright and joined by two snap-off tabs. Bore is 25.6 mm with a 2.6 mm wide, 0.8 mm deep internal rib 15 mm above the base that drops into the post groove; the outer taper runs 28.8 mm at the small end to 34 mm at the top over 46 mm, so any shelf collar whose bottom opening passes 28.8 mm wedges and locks as it slides down. Print one pair per post position (four pairs per shelf) to re-hang a shelf whose original clips cracked or went missing.
Chainsaw Bar Nose Scabbard
A slip-on scabbard for the tip of a chainsaw bar. It covers the front 128 mm of a 14–18 in bar that stands up to 76 mm tall with the chain on. The channel inside is 12 mm wide, and crush ribs grip the cutters, so it also fits 0.325 in and 3/8 in chain kerfs. A 5 mm cord eyelet lets you tie it to the saw's handle. It replaces a lost or cracked OEM bar cover for storage and transport.
Garage Door Emergency Release T-Handle
A red replacement for the T-handle on a sectional garage door opener's emergency-release cord. It has a 110 mm grip with finger scallops and a 50 mm stem. The cord runs through a 45° diamond channel that fits rope up to about 6.7 mm (the usual 5–6 mm opener cord). You can anchor it with a knot in the open 16 mm pocket, lock it with an M4 self-tapping pinch screw, or use both. The part prints flat so the pull load runs along the layers instead of across them.
125 mm Twin-608 Cart Wheel
A 125 mm diameter x 30 mm wide replacement wheel for hand trucks, garden carts, shop dollies and trash bins fitted with an M8 axle kit. It takes two 608 bearings (8 x 22 x 7 mm) press-fit into 22.05 mm pockets on each face and has a 9.5 mm through-bore for an 8 mm rod or M8 bolt. Six radial ribs over a flat web and a grooved 4 mm tread keep the weight around 90 cm³, and it prints flat with no supports.