Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Clothesline Prop Head For 1/2 in EMT
A 170 mm crossbar head that slides onto a 1/2 in EMT conduit pole (17.9 mm OD, 18.3 mm bore, 36 mm deep), so you can make a clothesline prop. It has four round-bottom line notches at 44 mm spacing to keep up to four lines apart, and an M4 self-tapping lock screw that stops the head from spinning on the pole.
Plant Support Ring Clamp For 1/2 in EMT Stake
A pinch-clamp collar for 1/2 in EMT conduit (17.9 mm OD, 18.4 mm bore) that holds an open 70 mm plant ring. You slip the ring around a tomato, pepper or dahlia stem through the 20 mm gate, then lock it at any height with an M5 bolt and a captured nut. The part is 130 mm long and prints flat, so the side load from the plant stays along the layers instead of across them.
3/4 in EMT Wagon Handle Pivot Clevis
This replaces the cracked folding pivot on a garden or utility wagon handle. One end is a 42 mm deep socket for a new handle made from 3/4 in EMT conduit (23.4 mm OD, bored to 23.7 mm), held by two M5 through-bolts. The other end is a clevis with an 18 mm wide jaw that takes the wagon's tongue tab and pivots on an 8 mm steel pin or M8 bolt (8.3 mm bore). For tabs thinner than 18 mm, pack the gap with M8 washers. The part prints on its side, so the handle pull runs along the layers and not across them. It measures 90 x 36 x 34 mm.
Dog Tie-Out Swivel Cap For 1/2 in EMT Stake
A print-in-place swivel head for a dog tie-out that slips over a 1/2 in EMT conduit stake (17.9 mm OD, 18.3 mm bore, 36 mm deep). It replaces the swivel eye that strips or snaps on corkscrew stakes, which are usually only sold as a whole kit. A 50 mm ring rides on a V-race with a 0.5 mm gap, so the 11 mm snap-hook eye turns a full 360° and the lead doesn't wind around the stake. The part is 45 mm tall, and the pull from the lead runs in the layer plane. There's an optional M4 self-tapping set-screw hole if you want to lock the cap onto the stake.
1/2 in EMT Three-Way Canopy Corner
A three-way corner connector for 1/2 in EMT conduit (17.9 mm OD). It has 18.4 mm sockets, 35 mm deep, on the +X, +Y and +Z axes, and each socket locks with an M4 thumbscrew in a brass heat-set insert. Use it to build shade canopies, bird-netting cages, cold frames and greenhouse frames from cheap hardware-store conduit. The horizontal bores have teardrop tops so it prints flat without supports, and the whole part is 69 x 61 x 65 mm.
EMT String Light Mast Bracket
A two-saddle wall bracket that carries a 3/4" EMT conduit mast (23.4 mm OD, 23.7 mm slip bore) flat against a deck post, 4x4 or fence rail for hanging café/string lights. 148 x 50 x 42 mm plate with six 5.5 mm holes for #10 wood screws (4.8 mm shank) or M5 bolts, saddle centres 104 mm apart, and an M5 pinch bolt with a captive 8 mm hex-nut pocket in the upper ear to lock the mast against sliding or spinning; the 18 mm throat is narrower than the conduit so the mast is threaded down through both cradles and stays captured.