Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Fridge Leftover Plate Stacking Ring
A vented 170 mm ring, 55 mm tall, that sits on the flat centre of a 10–11 in dinner plate of leftovers. A second plate stacks on its 11 mm chamfered top ledge, which has a 148 mm inner diameter, so you can stack two or three covered plates in the fridge without crushing the food. Twelve diamond vents let air through and keep the ring light, and two 45°-gusseted grip tabs make it easy to lift off.
Fridge Door Bin Clip-On Bottle Divider
A divider that clips onto the top edge of a fridge door bin and splits it into bays, so bottles and jars stop sliding and tipping every time the door swings. It has a 70 x 61 mm ribbed fin and a sprung outer jaw that grips any bin wall from 2 to 6 mm thick. The finger flexes in the print plane, so it won't snap along layer lines.
Fridge Crisper Drawer Lip Repair Glide Shoe
A 60 mm bolt-on J-profile shoe that replaces the snapped-off runner lip on a fridge crisper or freezer drawer side wall (Whirlpool, Kenmore, Frigidaire style clear drawers) so the drawer stops tipping and falling off its rail. The inner plate bolts to the inside of the drawer wall with two M3x10 screws and nuts through 3.4 x 10 mm vertical slots (6.6 mm of height adjustment to match the original lip), the 8 mm channel hooks over any wall up to 5 mm thick with room for the nut, and a 9.4 mm wide glide ledge hangs 6.6 mm below the bridge to ride the liner runner; print in PETG and drill two 3.5 mm holes through the drawer wall using the slots as a guide.
Fridge Glass Shelf Flex-Finger Edge Trim
Snap-on replacement front edge trim for a refrigerator glass shelf whose original plastic strip has cracked off. The 154 mm segment has a 2.4 mm thick, 18 mm tall front face with a 7 mm drip lip below the glass, a rigid rear jaw and nine 1.2 mm flex fingers whose bumps narrow the 5.3 mm slot to 3.9 mm so it grips 4–5 mm tempered shelf glass; segments dovetail together end to end to cover any shelf width, and the plate-flat print needs no supports. Print in PETG for cold-tolerant flex.
RV Fridge Three-Step Airing Prop
A red stepped wedge that holds an RV or camper fridge door 15, 25 or 35 mm ajar during storage, so the fridge doesn't grow mold. It replaces the airing card that keeps snapping, and it works without knowing the door latch geometry. The body is 75 x 35 x 18 mm with ribbed pockets, and the tab has a 6 mm hole so you can tie it to the door handle and it doesn't get lost.
Six-Egg Cone Cradle Fridge Tray
A 162 x 112 mm fridge tray that holds six eggs upright in thin-walled cone cradles. Each cradle is 47 mm across at the top and narrows to 24 mm, so medium to jumbo eggs sit point-down without touching. Each cup has a 23 mm drain and air hole, and an 8 mm stiffening rim runs around the edge so the tray slides onto a fridge shelf or door rack in place of a lost or cracked egg insert.
Fridge Can Stacker Bridge
A corrugated bridge that rests on a row of cans in the fridge and cradles a second layer on top, doubling shelf density without a wobbly stack. 140 mm wide x 48 mm deep x 27 mm tall: three arched saddles on the underside straddle the lower row, two 43-degree V-cradles on top hold the upper cans, and a 16 mm front lip stops them rolling out. The V geometry self-centres anything from 53 mm slim cans to 68 mm standard 12 oz cans and small bottles, so nothing depends on one exact diameter.