Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Range Hood Filter Snap Retaining Clip
A screw-on replacement for the broken clip that holds a baffle or mesh grease filter in an older range hood. It is a 58 x 14.5 x 22 mm spring-tongue latch. Two 4.5 mm M4/#8 clearance holes fix the 5 mm-thick tab to the hood. The filter frame edge slides under the angled lead-in and snaps under a catch that holds frame edges 3–7 mm thick. The profile is printed standing on its side, so the tongue flexes along the layers, not across them.
Slotted-Span Fridge Door Pull Handle
A 170 mm replacement pull handle for a refrigerator or freezer with a cracked or snapped handle. The two feet have 10 mm slots for M4 or #8 screws, so it fits screw spacings anywhere from 136 to 156 mm without drilling new holes. The bar stands 26 mm off the door to leave room for your fingers, and the screw heads sit in 9 mm counterbore channels you reach from the front. It prints flat, so the pulling force runs along the layers instead of across them.
Pull-Down Faucet Hose Split Weight
A two-piece weight that bolts onto the hose of a pull-down kitchen faucet, under the sink, so the sprayer pulls back into its dock again. It replaces the weight that slides off or gets lost and isn't sold on its own. Print two identical 80 x 40 x 16 mm halves. They fit braided hose of about 9–11 mm OD with grip ribs and close with four M4 x 25 cap screws and nuts. Two sealed 8 x 44 mm pockets inside hold steel BBs or scrap nuts set in hot glue to add weight.
150 mm Microwave Turntable Roller Ring
Replacement microwave turntable support ring for ovens whose glass tray rides on a 150 mm roller track. It has three 18 mm rollers on radial pins, a 168 mm OD ring and a loose 36 mm hub that drops over drive couplers up to about 34 mm. The ring, rollers and pins are all PLA with no metal inside. They print together on breakaway sprues: snap them off, drop each roller between its cheeks and push the headed 4 mm pin through, where the inner cheek grips it. The tray sits 18 mm above the floor and the ring clears it by 2.5 mm.
Brew-Through Universal Carafe Lid
A replacement lid for drip coffee carafes and pitchers whose original lid cracked or was lost. The tapered 2 mm skirt wedges into any round mouth from 58 to 76 mm inside diameter, and an 86 mm cap sits on top. The cap has a 14 mm brew-through centre hole, a 12 x 14 mm pour slot and a flat pull tab. The part is 97 x 86 x 30 mm. Before ordering, measure your carafe's inside mouth diameter; print it in PETG if it will hold hot coffee.
Screw-Lock 5 mm Shelf Support Pin Set
A snap-off sprue of four gusseted L-bracket shelf supports for kitchen cabinets with standard 5 mm shelf-pin holes. Each one has a 9 mm octagonal pin measuring 4.6 mm across the flats and 5 mm across the corners, plus an 18 x 10 mm shelf seat with a 4 mm through-hole: drive a #6 (3.5 mm) screw up into the shelf so it can't tip or slide off. The pieces print flat, so shelf load goes along the layers, not across them.
M5 Bolt-Pin Cooler Lid Hinge Leaf
A universal replacement hinge for picnic and ice-chest lids. Both halves are the same part: print two, turn one 180° and interleave the four 14.5 mm knuckles. The pin is an M5 x 65–70 mm bolt with a nylock nut through the 5.5 mm bore. Each 60 x 40 mm leaf mounts with three #8 pan-head screws, and the 4.8 x 9 mm slots give ±2 mm to line up with the old holes. The knuckles leave clearance for the lid to swing past 90°. Print in PETG or ASA.
Cone-Seat Kitchen Sink Strainer Basket
A drop-in sink strainer basket that replaces a cracked or rusted basket in a standard 3.5 in (about 90 mm) kitchen sink drain. It has no fixed diameter to match: a 45° conical seat centres it in any drain opening from 72 to 108 mm across. The basket is 108 mm across and 46.5 mm tall. It has 12 radial floor slots, 16 wall slots and a 16 mm lift knob, and sits about 36 mm deep in a 90 mm opening.
Step Can Pedal Rocker Arm
Replacement rocker/bell-crank arm for the foot-pedal linkage in a step trash can (Simplehuman-style 30 L round cans and their clones), the one plastic lever that always snaps and that nobody sells as a service part. 98.7 mm long with a 5.5 mm pivot bore for a 5 mm pin or M5 bolt, two 4.5 mm pedal-rod holes 9 mm apart to re-tune pedal throw, and an open C-socket at the lift end that clips over a 4 mm lid rod; 10 mm tall bosses and a full-length spine rib carry the load in the print plane. Measure your can's pivot pin before printing — holes are sized to standard 4 mm / 5 mm pins.
Sous Vide Circulator Rim Clamp
Replacement pot clamp for a sous vide circulator whose OEM plastic clamp has snapped — a 38 x 80 x 46 mm C-clamp that hooks over any pot wall or Cambro/Rubbermaid tub rim up to 18 mm thick and locks down with an M4 thumbscrew running in a 5.5 mm heat-set insert bore. A 90° V-channel cradles any circulator barrel from 40 to 70 mm diameter and two 9 x 4 mm slots take a zip tie or velcro strap to bind the barrel into the V. The C-profile lies in the bed plane so the clamping load runs along the layer lines, not across them.